Arcteq AQ-F213 Скачать руководство пользователя страница 376

Страница: 376 / 455

Currents

Description

Rseq, Xseq, Zseq

RseqAng, XseqAng, ZseqAng

The positive sequence resistance, reactance and impedance values and angles.

GL1, GL2, GL3, G0

BL1, BL2, BL3, B0

YL1, YL2, YL3, Y0

The conductances, susceptances and admittances.

YL1angle, YL2angle, YL3angle

Y0angle

The admittance angles.

Others

Descrip

Description

tion

System f.

The tracking frequency in use at that moment.

Ref f1

The reference frequency 1.

Ref f2

The reference frequency 2.

M thermal T

The motor thermal temperature.

F thermal T

The feeder thermal temperature.

T thermal T

The transformer thermal temperature.

RTD meas 1…16

The RTD measurement channels 1…16.

Ext RTD meas 1…8

The external RTD measurement channels 1…8 (ADAM module).

Reported values

When triggered, the function holds the recorded values of up to eight channels, as set. In addition to

this tripped stage, the overcurrent fault type and the voltage fault types are reported to SCADA.

Q-F213

-F213

Instruction manual

Version: 2.04

375

Содержание AQ-F213







































































































































































































































































































































































































































































Результаты поиска

Содержание AQ-F213

Отзывы:

Бренды по названию

Популярные бренды

Arcteq AQ-F213, Инструкция по эксплуатации

Результаты поиска

Содержание AQ-F213

Отзывы:

Бренды по названию

Популярные бренды