Arcteq AQ-F213 Скачать руководство пользователя страница 4

Страница: 4 / 455

9.1.2.1 Auxiliary voltage.......................................................................................... 423

9.1.2.2 CPU communication ports.......................................................................... 424

9.1.2.3 CPU digital inputs ....................................................................................... 425

9.1.2.4 CPU digital outputs..................................................................................... 425

9.1.3 Option cards ........................................................................................................... 426

9.1.3.1 Digital input module .................................................................................... 426

9.1.3.2 Digital output module.................................................................................. 427

9.1.3.3 Arc protection module ................................................................................ 427

9.1.3.4 Milliampere module (mA out & mA in) ......................................................... 428

9.1.3.5 RTD input module....................................................................................... 429

9.1.3.6 RS-232 & serial fiber communication module.............................................. 429

9.1.3.7 Double LC 100 Mbps Ethernet communication module ...............................429

9.1.4 Display .................................................................................................................... 429

9.2 Functions........................................................................................................................... 430

9.2.1 Protection functions................................................................................................. 430

9.2.1.1 Non-directional overcurrent protection (I>; 50/51)....................................... 430

9.2.1.2 Non-directional earth fault protection (I0>; 50N/51N) .................................. 431

9.2.1.3 Directional overcurrent protection (Idir>; 67)............................................... 432

9.2.1.4 Directional earth fault protection (I0dir>; 67N/32N) ..................................... 433

9.2.1.5 Negative sequence overcurrent/ phase current reversal/ current unbalance

protection (I2>; 46/46R/46L)................................................................................... 434

9.2.1.6 Harmonic overcurrent protection (Ih>; 50H/51H/68H)................................. 434

9.2.1.7 Circuit breaker failure protection (CBFP; 50BF/52BF) ................................. 435

9.2.1.8 Low-impedance or high-impedance restricted earth fault/ cable end differential

protection (I0d>; 87N) ............................................................................................ 436

9.2.1.9 Overvoltage protection (U>; 59) ................................................................. 437

9.2.1.10 Undervoltage protection (U<; 27) ............................................................. 437

9.2.1.11 Neutral overvoltage protection (U0>; 59N)................................................ 438

9.2.1.12 Sequence voltage protection (U1/U2>/<; 47/27P/59NP) ...........................439

9.2.1.13 Overfrequency and underfrequency protection (f>/<; 81O/81U)................440

9.2.1.14 Rate-of-change of frequency protection (df/dt>/<; 81R).............................440

9.2.1.15 Line thermal overload protection (TF>; 49F).............................................. 441

9.2.1.16 Overpower (P>; 32O), underpower (P<; 32U) and reverse power (Pr; 32R)

protection............................................................................................................... 442

9.2.1.17 Resistance temperature detectors ............................................................ 443

9.2.1.18 Arc fault protection (IArc>/I0Arc>; 50Arc/50NArc) (optional).....................443

9.2.1.19 Voltage memory ....................................................................................... 444

9.2.2 Control functions ..................................................................................................... 444

9.2.2.1 Setting group selection ............................................................................... 444

9.2.2.2 Object control and monitoring..................................................................... 445

9.2.2.3 Auto-reclosing (0

→

1; 79) ......................................................................... 445

9.2.2.4 Cold load pick-up (CLPU)........................................................................... 446

9.2.2.5 Switch-on-to-fault (SOTF) ........................................................................... 446

9.2.2.6 Vector jump (Δφ; 78) .................................................................................. 446

9.2.3 Monitoring functions ................................................................................................ 447

9.2.3.1 Current transformer supervision ................................................................. 447

9.2.3.2 Voltage transformer supervision (60) .......................................................... 448

9.2.3.3 Circuit breaker wear monitoring .................................................................. 448

9.2.3.4 Total harmonic distortion............................................................................. 449

9.2.3.5 Fault locator (21FL) .................................................................................... 449

9.2.3.6 Disturbance recorder.................................................................................. 450

9.3 Tests and environmental .................................................................................................... 450

tion ..............................................................................................................

.............................................................................................................. 453

453

11 Contact and r

11 Contact and reeffer

erence inf

ence informa

ormation

tion..........................................................................................

.......................................................................................... 454

454

Q-F213

-F213

Instruction manual

Version: 2.04

Содержание AQ-F213







































































































































































































































































































































































































































































Результаты поиска

Содержание AQ-F213

Отзывы:

Бренды по названию

Популярные бренды

Arcteq AQ-F213, Инструкция по эксплуатации

Результаты поиска

Содержание AQ-F213

Отзывы:

Бренды по названию

Популярные бренды