manualshive.com logo in svg

Aquaread Aquaprobe Lite, Инструкция по эксплуатации

Поделиться
Скачать
Aquaread Aquaprobe Lite Скачать руководство пользователя страница 8

Aquaprobe

®

 Lite Instruction Manual

10401-00976  Rev F

Another particular problem when trying to measure very low 
concentrations is air in the form of both visible and 
microscopic bubbles. These act like tiny prisms and can 
refract and reflect both the excitation light and the return 
signal being measured. 

The photograph to the right was taken in a calibration tube 
after fresh water was poured in. The bubbles are clearly 
visible in the light beam.

2.4. Top Tips for successful measurements using optical electrodes

Always keep the measurement chamber and electrode lenses clean.

Always fit the sleeve and end cap during both calibration and measurement.

Always   allow   the   readings   to   settle   completely   during   both   calibration   and 
measurement.

Always try to eliminate air bubbles by agitating the Probe after insertion both during 
calibration and measurement. On the AP-7000, activate the self-cleaning mechanism to 
clear bubbles.

Always   calibrate   and   zero   the   electrode   as   close   to   your   sample   temperature   as 
possible. This is especially important with the Ref-Oil electrode.

Always zero the electrode just prior to use in clean water (bottled still mineral water is  
ideal). This is also especially important with the Ref-Oil electrode.

2.5. About Fluorescent Measurement

All Optical Electrodes, with the exception of the Turbidity Electrode, employ fluorescent 
measurement techniques. Interference from microbiological species and compounds which 
fluoresce at similar wavelengths and differences in fluorescence caused by temperature, 
ambient light and turbidity can all cause inaccuracies. 

Fluorescence measurement is ideal for researchers who are interested in detecting the 
presence or absence of a specific substance in reasonable concentrations and measuring 
relative fluorescence changes that can be used as an indication of increasing or decreasing 
concentrations. 

Fluorescence measurement techniques are not ideal for quantitative measurement and it is 
therefore impossible to specify an absolute accuracy.

In order to obtain accurate results, data obtained with a fluorescent electrode in the 
field must be post-calibrated with data from standard laboratory analysis of grab 
samples acquired during the study. 

© 2015 Aquaread

®

 Ltd.

www.aquaread.com

Page 8 of 72

Содержание Aquaprobe Lite









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды