background image

3

9.     Keep fingers away from a running unit; 

        fast moving and hot parts will cause injury 

        and/or burns.
10.  If the equipment starts to vibrate abnormally, 

        STOP the motor and check immediately for 

        the cause. Vibration is generally an indication 
        of trouble.

Fogging Precautions

DANGER

A motionless atomizer may 

appear safe, but its blade 

could suddenly begin high-

speed rotation without 

warning as a result of 

control programming.

When a GT 500-HS is automated by controls, 

warning signs should be posted near the high-

speed equipment.

Disconnect and lock out power source to inspect 

or service the unit.

G

ENERAL

 S

AFETY

Since the GT 500-HS uses high-speed components 

to atomize liquids, the following safety precautions 

must be observed at all times:

1.  Read all manuals included 

     with this product. Be familiar 

     with the product and controls.

2.  Follow United States  

 

     Environmental Protection Agency (EPA)    

     guidelines and regulations when fogging   

     pesticide or chemical solutions.

3.  Follow all local electrical and safety codes 

     as well as the United States National  

 

     Electrical Codes (NEC) and Occupational  Safety  

     and Health Act (OSHA).

4.  Only persons well acquainted with these 

     rules of safe operation should be allowed to 

     use the atomizer.

5.  Keep visitors away and NEVER allow children in 

     the work area.

6.  Before each use, inspect blade assembly 

     and electrical components for signs of damage, 

     deterioration, weakness or leakage. Repair or 

     replace defective items before using.

7.  Check all fasteners at frequent intervals for 

     proper tightness.

MOTORS, ELECTRICAL EQUIPMENT AND 

CONTROLS CAN CAUSE ELECTRICAL 

ARCS THAT WILL IGNITE FLAMMABLE 

LIQUID OR GAS. NEVER OPERATE OR 

REPAIR IN OR NEAR FLAMMABLE LIQUID OR GAS. 

NEVER STORE FLAMMABLE LIQUIDS OR GASES IN THE 

VICINITY OF THE ATOMIZER.

DO NOT ATOMIZE

FLAMMABLE MATERIALS.

1.     Humidity and cold air are

        two common asthma triggers.    

 

        Asthmatic people working  

 

 

        with this equipment need to

        be made aware of the risk.
2.     When atomizing toxic chemicals, follow  the  

        instructions provided by the chemical    

        manufacturer.

NEVER OPERATE THE

GT 500-HS WITHOUT THE 

SAFETY GUARD IN PLACE IF THE UNIT IS LOWER THAN 

SEVEN FEET ABOVE WORKING HEIGHT.

WARNING

WARNING

DANGER

HIGH-SPEED ROTATION

www.JigglyGreenhouse.com  |  (800) 878-7829  |  [email protected]

Содержание GT 500-HS



















Отзывы: