APRILIA M191M Скачать руководство пользователя страница 96

Страница: 96 / 177

ENGINE

3 - 72

Engines M192M / M191M / M245M / M234M / M282M / M281M

3.5.3.

OPENING THE CRANKCASE

•

Remove the crankcase coupling screws (1).

•

Detach the two casings. Keep the shaft (2) installed on
one of them.

WARNING
The crankshaft may drop out if this is not done.

•

Remove the crankshaft.

NOTE

The crankshaft of the 200 cc version is installed with

two re-timing steel washers. Mark washers assembly posi-
tion.

WARNING
When opening the crankcase and removing the
crankshaft, make sure that its threaded ends do
not damage the main bearings.

•

Remove the oil precleaner.

•

Remove the screws and guard.

•

Remove the flywheel-side oil seal.

•

Remove the oil pressure sensor.

•

Remove the oil filter.

•

Remove flywheel-side oil seal.

•

Check the con-rod axial play.

Standard play: 0.20 ÷ 0.50 mm

Содержание M191M


















































































































































































Результаты поиска

Содержание M191M

Отзывы:

APRILIA M191M, Руководство по ремонту, Страница: 96 / 177

Результаты поиска

Содержание M191M

Отзывы: