APRILIA M191M Скачать руководство пользователя страница 82

Страница: 82 / 177

ENGINE

3 - 58

Engines M192M / M191M / M245M / M234M / M282M / M281M

3.3.8.

ASSEMBLING THE OIL PUMP

•

Check the pump body-shaft for wear.

•

Check that pump cover is not worn or scored.

•

In case of excessive wear or scores, change the dam-
aged parts or the whole unit.

•

Fit the pump cover so as to align the holes of the at-
tachment screws.

TIGHTENING TORQUE VALUES

Pump cover screws: 0.7 ÷ 0.9 Nm.

•

Make sure that gasket is correctly positioned and refit
pump to crankcase. Pump can be positioned in one
way only. Tighten screws to the specified torque.

TIGHTENING TORQUE VALUES

Pump retaining screws: 5 ÷ 6 Nm.

•

Fit washer and sprocket with a new O-ring.

•

Fit chain in the turning direction indicated when disas-
sembling.

•

Fit pulley, Belleville washer and center screw. Tighten
to the specified torque.

TIGHTENING TORQUE VALUES

Pulley screw: 10 ÷ 14 Nm

NOTE

Fit the Belleville washer, with its outer edge resting

against the pulley. Check that pump turns freely.

•

To refit the pump cover guard, tighten the two screws
to the specified torque.

TIGHTENING TORQUE VALUES

Cover guard screws: 0.7 ÷ 0.9 Nm

Содержание M191M


















































































































































































Результаты поиска

Содержание M191M

Отзывы:

Бренды по названию

Популярные бренды

APRILIA M191M, Руководство по ремонту

Результаты поиска

Содержание M191M

Отзывы:

Бренды по названию

Популярные бренды