manualshive.com logo in svg

APRILIA M191M, Руководство по ремонту

Поделиться
Скачать
APRILIA M191M Скачать руководство пользователя страница 131

 

 

ENGINE

3 - 107

Engines M192M / M191M / M245M / M234M / M282M / M281M

Standard clearance 

Intake: 0.013 ÷ 0.040 mm 
Exhaust: 0.025 ÷ 0.052 mm 
 

Max. allowed clearance 

Intake: 0.062 mm 
Exhaust: 0.072 mm 
 

• 

Check the surface mating the shim joint terminal for 
wear. 

 

Valve standard length (L – l) 

L (Engines M192M / M245M / M281M / M234M / M282M) 
(125 - 200 cc)=Intake: 94.6 mm 
L (Engine M191M) (150 cc)=Intake: 80.6 mm 
l (Engines M192M / M245M / M281M / M234M / M282M) 
(125 - 200 cc)=Exhaust: 94.4 mm 
l (Engine M191M) (150 cc)=Exhaust: 79.6 mm 

 

 

• 

If after the above checks all the values are within the 
specified limits, use the same valves. To ensure per-
fect sealing, grind valves with fine emery cloth. When 
grinding, position the head with the valve axes in hori-
zontal position to prevent emery cloth residues from 
entering the valve guide stem coupling (see figure). 

 

 

 

WARNING 
To avoid scoring the mating surface, do not 
overturn valve when the emery cloth is fin-
ished. Thoroughly wash head and valves with a 
product suitable to the emery cloth used. 

 

NOTE 

Do not confuse valve-assembling position. 

 

 

Содержание M191M


















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды