APRILIA M191M Скачать руководство пользователя страница 83

Страница: 83 / 177

ENGINE

3 - 59

Engines M192M / M234M / M282M

3.3.9.

ASSEMBLY OF THE CHAINS HOUSING

COVER (ENGINES M192M / M234M / M282M)
(125 - 200 cc)

•

Prepare the new cover and lubricate the sealing edge.

WARNING
Do not lubricate the surface used to key the
cover on the engine housing.

•

Preassemble the cover with the special tool and bring
the screws together.

•

Insert the tool bush on the drive shaft.

•

Insert the complete cover tool on the drive shaft until
contact is made with the housing.

WARNING
Set the cover with the chain channel down-
wards. If this is not done, the oil shield lead
sheath will be incorrectly positioned.

•

Install the tool bracket to correctly position the cover.

•

Screw the threaded bar right down on the drive shaft.

•

Use the nut on the base of the tool to check that the
cover is driven fully home.

•

Remove the tools.

WARNING
Failure to comply with this assembly procedure
is likely to result in serious damage to the en-
gine due to incorrect tightening of the oil pump
drive chain.

Содержание M191M


















































































































































































Результаты поиска

Содержание M191M

Отзывы:

APRILIA M191M, Руководство по ремонту, Страница: 83 / 177

Результаты поиска

Содержание M191M

Отзывы: