manualshive.com logo in svg

APRILIA M191M, Руководство по ремонту

Поделиться
Скачать
APRILIA M191M Скачать руководство пользователя страница 176

 

 

UPDATING ENGINES M192M / M191M 

4 - 30 

Engines M192M / M191M

• 

Mount the camshaft drive pulley with its washer. 

• 

Ensure that the 2V mark on the camshaft pulley is in 
line with the mark on the head. If the mark on the cam-
shaft is opposite the mark on the head, turn the drive 
shaft once. 

 

 

 

• 

Mount the counterweight. Tighten the attachment 
screw to the specified torque value. 

 

TIGHTENING TORQUE VALUE 

Screw: 7 ÷ 8,5 Nm 
 

• 

Mount the automatic valve-lifter body with its end-of-
travel washer and restrain the return spring. 

• 

Mount the valve-lifter body stop cup and tighten the 
screw to the specified torque value. 

 

TIGHTENING TORQUE VALUE 

Screw: 11 ÷ 15 Nm 
 

 

 

• 

Remove the central screw with the washer and tight-
ener spring. Check the one-way mechanism for signs 
of wear. 

• 

Check the soundness of the tightener spring. 

• 

If necessary, change the entire unit. 

• 

Press the locking tooth and bring the tightener block 
fully home. 

• 

Mount a new gasket and the chain stretcher. Tighten 
the attachment screws to the specified torque value. 

 

TIGHTENING TORQUE VALUE 

Screws: 11 ÷ 13 Nm 
 

 

 

• 

Position the spring and the washer. Tighten the central 
screw to the specified torque value. 

 

TIGHTENING TORQUE VALUE 

Screw: 5 ÷ 6 Nm 
 

• 

Mount the tappets cover. 

• 

Mount the washer separating the pinions, the O-ring on 
the drive shaft, the oil pump pulley cover, the oil sump 
with spring and by-pass piston, the starter pinion, the 
driving pulley with belt, and the transmission cover. 

 

 

 

Содержание M191M


















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды