Anywire ASLINKSENSOR, Руководство пользователя

Страница: 9 / 16

-B284SB0*1K**P30 9/16-
Parameter setting
■
Alarm bit selection setting
[Equipment parameter 1]
If you set this parameter to “enabled,” the number of occupied input points is
increased by one. When the alarm (ALM) indicator lamp lights, the alarm bit
turns ON to indicate the alarm status to the controller.
Alarm detecting conditions are specified by equipment parameters 11, 12 and 14.
Alarm bit disabled
Alarm bit enabled
Variable Description
0
100 Factory setting: 0
Input 1 point Input
n n+1
Input 2 points Input 1 Input 2
Input 1 point
Input
Offset address
Type
Offset address
Alarm
n n+1
Input 2 points
Input 1 Input 2
Type
n+2
Alarm
[When enabled] [When disabled]
This parameter is used to set an upper limit value of pressure detection input 0.
For both hysteresis mode and window comparator mode
→
Refer to equipment
parameter 8.
■
Input 0 upper limit setting
[Equipment parameter 2]
■
B284SB-01-1KPP30, B284SB-02-1KPP30
■
B284SB-01-1KNP30, B284SB-02-1KNP30
Variable Description
0 to 1000 0 to -100kPa Factory setting: 600 (-60kPa)
Variable Description
0 to 1000 0 to 1000kPa Factory setting: 600 (600kPa)
Variable Description
0 to 1000 0 to 100kPa Factory setting: 600 (60kPa)
Variable Description
0 to 1000 -100 to 100kPa Factory setting: 600 (20kPa)
■
B284SB-01-1KLP30, B284SB-02-1KLP30
■
B284SB-01-1KPLP30, B284SB-02-1KPLP30
This parameter is used to set a lower limit value of pressure detection input 0.
For both hysteresis mode and window comparator mode
→
Refer to equipment
parameter 8.
■
Input 0 lower limit setting
[Equipment parameter 3]
*This parameter cannot be set larger than the input 0 upper limit value (equipment parameter 2).
■
B284SB-01-1KPP30, B284SB-02-1KPP30
■
B284SB-01-1KNP30, B284SB-02-1KNP30
■
B284SB-01-1KLP30, B284SB-02-1KLP30
■
B284SB-01-1KPLP30, B284SB-02-1KPLP30
Variable Description
0 to 1000 0 to 100kPa Factory setting: 400 (40kPa)
Variable Description
0 to 1000 -100 to 100kPa Factory setting: 400 (-20kPa)
Variable Description
0 to 1000 0 to -100kPa Factory setting: 400 (-40kPa)
Variable Description
0 to 1000 0 to 1000kPa Factory setting: 400 (400kPa)
■
B284SB-02-1KPP30
■
B284SB-02-1KNP30
■
B284SB-02-1KLP30
■
B284SB-02-1KPLP30
Variable Description
0 to 1000 0 to 100kPa Factory setting: 400 (40kPa)
Variable Description
0 to 1000 -100 to 100kPa Factory setting: 400 (-20kPa)
Variable Description
0 to 1000 0 to -100kPa Factory setting: 400 (-40kPa)
Variable Description
0 to 1000 0 to 1000kPa Factory setting: 400 (400kPa)
Variable Description
2
3
0
1
Variable Description
0
1 Factory setting: 0
This parameter is used to set an upper limit value of pressure detection input 1.
(For input 2 points type only)
For both hysteresis mode and window comparator mode
→
Refer to equipment
parameter 8.
■
Input 1 upper limit setting
[Equipment parameter 4]
■
B284SB-02-1KPP30
■
B284SB-02-1KNP30
■
B284SB-02-1KLP30
■
B284SB-02-1KPLP30
Variable Description
0 to 1000 0 to 100kPa Factory setting: 600 (60kPa)
Variable Description
0 to 1000 -100 to 100kPa Factory setting: 600 (20kPa)
Variable Description
0 to 1000 0 to -100kPa Factory setting: 600 (-60kPa)
Variable Description
0 to 1000 0 to 1000kPa Factory setting: 600 (600kPa)
This parameter is used to set a lower limit value of pressure detection input 1.
(For input 2 points type only)
For both hysteresis mode and window comparator mode
→
Refer to equipment
parameter 8.
■
Input 1 lower limit setting
[Equipment parameter 5]
Hysteresis mode
Window comparator mode
Input 0: Hysteresis mode, Input 1: Hysteresis mode
Input 0: Window comparator mode, Input 1: Hysteresis mode
Input 0: Hysteresis mode, Input 1: Window comparator mode
Input 0: Window comparator mode, Input 1: Window comparator mode
This parameter is used to set the hysteresis mode and/or window comparator
mode of input 0 and input 1.
■
Operation mode selection
[Equipment parameter 8]
*For details, refer to page 11 to 12.
■
B284SB-01-1KPP30, B284SB-01-1KNP30, B284SB-01-1KLP30, B284SB-01-1KPLP30
■
B284SB-02-1KPP30, B284SB-02-1KNP30, B284SB-02-1KLP30, B284SB-02-1KPLP30
* This parameter cannot be set larger than the input 2 upper limit value (equipment parameter 4).
Factory setting: 0