background image

n+1

n+2

n

B284SB-02-1K

□□

P30

n+1

n

-B284SB0*1K**P30  11/16-

0

0

1000

1000

0

0

1000

-100

0

1000

500

100

0

-100

0

0

1000

100

B284SB-01-1K

□□

P30

1000

OFF

ON

0

0

1000

OFF

ON

0

1000

OFF

ON

Description

Address

offset

Alarm

bit

[Data Configuration]

Input 1 Input 0

This unit also send a digital value of measured pressure to the “sensing level area*

1

” 

of the master unit.

Digital value of measured pressure: 0 to 1023 (0Hex to 3FFHex)

 Sensing level

Sensing

level

Digital value of measured pressure (16-bit binary data)

*n = Bit address number set in this unit

Description

Address

offset

Alarm

bit

Input 0

Status

details

Status detail area of the master unit

b0: Slave unit voltage drop (DP-DN-side voltage drop)
b1: Sensing level drop

*1  This can be used on the master unit having the sensing level and the status detail area. 

For details, refer to the manual of the master unit.

b14

b15

b1

b2

b0

b3

b4

b5

b6

b7

b8

b9

b10

b11

b12

b13

 Status details

The contents of an alarm detected with this unit can be checked with the “status 

detail area*

1

” on the master unit.

A bit corresponding to the status detail area turns ON depending on the contents 

of the alarm.

Hysteresis mode (Equipment parameter 8: 0)
Positive logic 

(Equipment parameter 9: 0)

Window comparator mode  (Equipment parameter 8: 1)
Positive logic 

(Equipment parameter 9: 0)

Hysteresis mode (Equipment parameter 8: 0)
Negative logic 

(Equipment parameter 9: 1)

Input pressure 0
(upper limit)

Input pressure 0
(lower limit)

Input 0
(sensor output 0) 

Input pressure 0
(upper limit)

Input pressure 0
(lower limit)

Input 0
(sensor output 0) 

Input pressure 0
(upper limit)

Input pressure 0
(lower limit)

Input 0
(sensor output 0) 

[Examples of Operations]

Range

Range

Range

Time

Pressure detected by sensor

Input 1 point type

Time

Pressure detected by sensor

Input 1 point type

Input 1 point type

Time

Pressure detected by sensor

B284SB-01-1KPP30, B284SB-02-1KPP30

B284SB-01-1KLP30, B284SB-02-1KLP30

B284SB-01-1KNP30, B284SB-02-1KNP30

B284SB-01-1KPLP30, B284SB-02-1KPLP30

Input pressure (kPa)

Input pressure (kPa)

Sensing level
Digital value of measured pressure

Sensing level
Digital value of measured pressure

Sensing level
Digital value of measured pressure

Sensing level
Digital value of measured pressure

Input pressure (kPa)

Input pressure (kPa)

Содержание ASLINKSENSOR

















Отзывы: