Antunes VCT-2 Скачать руководство пользователя страница 13

Страница: 13 / 24

P/N 1011308 Rev. E 11/16

QUARTERLY CLEANING

The Quarterly Cleaning involves clean-

ing the interior of the unit. Follow these

steps.

1. Turn the unit off, unplug the

power cor,d and allow the unit to

cool down.

2. Put on heat resistant gloves.

Remove the Bun Feeder, Release

Sheet, and Bun Chute (Figure 6).

Set these item aside.

3. Set both Bun thickness Compres-

sion Knobs to 6. Next, open both

Conveyor Covers (Figure 7).

4. Remove both Belt wraps - lift the

flap on the Belt Wrap and pull the

Belt Wrap Pin out of the zipper

(Figures 8). Disconnect the Belt

Wrap clips from the Conveyor

Belt Chain and remove the Belt

Wraps from the toaster (Figure 8).

5. Inspect the Belt Wraps for rips

or tears. If the Belt Wraps are in

good condition, set them aside.

They will be reinstalled onto the

toaster later in this process.

6. Disconnect the Conveyor Belt

chains by squeezing any two

links together and unhooking

both ends of the one link (Figure

14). Pliers may be used. Remove

the Conveyor Belt Chains and set

aside.

7. Use Hi-Temp Detail Brush (Ecolab

item# 92212765) to carefully

remove all debris and residue

from the inside components of

the toaster (Figure 15). Do this on

both sides of the toaster.

NOTE:

With proper and regular daily

and monthly cleaning, the inte-
rior of toaster should be free of
residue and debris. If you find
that the interior is extremely
dirty on a regular basis, please
review how the daily and
monthly the frequency and dai-
ly and monthly cleaning steps.

8. Reassemble the Conveyor Belt

Chain onto the sprockets.

NOTE:

Make sure the Conveyor Belt

Chain hooks are pointing
DOWN as shown in Figure 10.

Figure 14

Figure 15

USE A HI-TEMP DETAIL BRUSH (ECOLAB

ITEM# 92212765) TO CAREFULLY REMOVE

ALL DEBRIS AND RESIDUE FROM THE

INSIDE OF THE TOASTER.

DO THIS ON BOTH SIDES OF THE TOASTER.

9. Reinstall the Belt Wraps onto the

toaster under the yellow rods

and making sure the flap is point-

ing down.

10. Connect the Belt Wrap clips to

the Conveyor Belt Chain.

11. Then, reconnect the ends of the

Belt Wraps with the Belt Wrap

Pin, making sure the zipper teeth

are properly aligned (Figure 13).

NOTE:

Make sure the Belt Wraps are

installed under the yellow rods.

12. Close the Conveyor Covers.
13. Reinstall the Release Sheet, Bun

Chute, and Bun Feeder and re-

turn the toaster to operation.

Содержание VCT-2

























Результаты поиска

Содержание VCT-2

Отзывы:

Похожие инструкции для VCT-2

Бренды по названию

Популярные бренды

Antunes VCT-2, Руководство пользователя

Результаты поиска

Содержание VCT-2

Отзывы:

Похожие инструкции для VCT-2

Бренды по названию

Популярные бренды