Antunes VCT-2 Скачать руководство пользователя страница 9

Страница: 9 / 24

P/N 1011308 Rev. E 11/16

MAINTENANCE

WARNING

The unit will remain hot while it is cooling

down. Personal injury and burns may result

from touching the unit before it is finished
cooling down. Wear Heat Resistant Gloves.

DAILY MAINTENANCE

NOTE:

The following are general

maintenance procedures.
For additional details includ-
ing approved chemicals,
please see the Toaster Pro-
cedure documents by scan-
ning the QR Code on the
front page of this manual.

The daily maintenance steps involve:

Cleaning the Accessories and

Toaster

Cleaning the Release Sheet

Cleaning the Accessories and Toaster

1. Turn the toaster off and allow it

to cool before proceeding.

2. Refer to Figure 3. Remove the

Bun Feeder, Release Sheet, and

Bun Chute and set aside.

NOTE:

Do not wash the Release

Sheet in the sink. It must
be washed by hand.

3. Wash the Bun Feeder and Bun

Chute in soap and water. Rinse

with clean water and allow to air

dry.

4. Wipe all surfaces of the unit with

a hot damp cloth.

NOTE:

Do not use a dripping wet

cloth. Wring out before use.

Cleaning the Release Sheet

1. Inspect the Release Sheet.

Replace the Release Sheet if it is

worn, creased, or torn.

2. Spray an approved cleanser on a

clean, dry towel.

3. Wipe the Release Sheet firmly

from top to bottom.

4. Repeat this procedure with a

clean, dry towel dampened with

water.

5. Next, wipe the release sheet with

a clean towel dampened with an

approved sanitizer. Allow to air

dry.

6. Repeat Steps 1 through 6 on the

inside portion of the Release

Sheet. Set the clean Release

Sheet aside.

Cleaning the Belt Wraps

7. Open the front and rear Convey-

or Covers (Figure 4a)

8. Inspect the front and rear Belt

Wraps. Replace the Belt Wraps

if there are any signs of tearing,

folding, or other damage.

9. Turn on the unit.

NOTE:

This step requires that the

toaster be turned on with the
Conveyor Covers open. Use
caution during these steps.

10. Spray a clean, sanitized towel

with an approved cleanser and

wipe the front and rear Belt

Wraps for one full rotation.

11. Repeat Step 4 with an approved

sanitizer.

NOTE:

Repeat these steps as needed

until the Belt Wraps are clean
and tacky/sticky to the touch.

12. Reinstall the Release Sheet, Bun

Chute, and Bun Feeder and re-

turn the toaster to operation.

Cleaning the Rear Fan
Use a clean dry cloth and wipe the fan

intake. If there is heavy debris buildup,

use an Ecolab Detail Brush (item#

92212765) followed by a clean, dry

cloth (see Figure 4b).

Figure 3

Figure 4a

Figure 4b

Содержание VCT-2

























Результаты поиска

Содержание VCT-2

Отзывы:

Похожие инструкции для VCT-2

Бренды по названию

Популярные бренды

Antunes VCT-2, Руководство пользователя

Результаты поиска

Содержание VCT-2

Отзывы:

Похожие инструкции для VCT-2

Бренды по названию

Популярные бренды