Anest Iwata MSU-323 C Скачать руководство пользователя страница 3

3

USE OF THE 

 

The use and maintenance manual is the document accompanying the equipment from its manufactu-

MANUAL

 

re till its dismantling. Therefore, it is an integral part of the equipment. 

 

The manual must be read before starting ANY ACTIVITY involving the equipment including its hand- 

 ling.

 
 

WARNING

 

THE ORIGINAL CONFIGURATION OF THE EQUIPMENT MUST NOT BE CHANGED AT ALL.

 
 

On receiving the equipment check that:

 

The supply corresponds to the order specifications.

 

In case of non-compliance, inform immediately our TECHNICAL SERVICES.

 
 

WARNING 

 

ALL RIGHTS ARE RESERVED. THE REPRODUCTION OF ANY PART OF THIS MANUAL, IN ANY  

 

FORM, IS STRICTLY FORBIDDEN WITHOUT PRIOR WRITTEN AUTHORIZATION OF THE  

 

 

MANUFACTURING COMPANY. 

    

WARRANTY 

 

All 

ANEST IWATA 

products have a one-year guarantee from the invoice date, unless otherwise stated 

 

in writing. The warranty covers all manufacturing faults and material defects. 

 

Any spare part replacement or repair operations are covered only if they are carried out by our techni- 

 

cians at our servicing shops.

 

The faulty parts must be sent CARRIAGE PAID.

 

Once the components have been repaired, they will be sent CARRIAGE FORWARD to the customer.

 

The warranty covers no intervention of our technicians during installation or dismantling operations.  

 

If for practical purposes one of our technicians is sent on site, a charge will be made for the time    

 

plus extra for travelling and expenses.

 

Our warranty does not cover direct or indirect damage to people or property caused by our equiment.  

 

It covers no repair operations carried out by the customer or by a third party, either.

 

THE WARRANTY DOES NOT COVER:

 

-  Damage or breakdown caused by improper use or assembly.

 

-  Damage or breakdown caused by the use of spare parts that are different from the original or  

 

   

 

  recommended ones.

 

-  Damage or breakdown caused by a bad preservation.

 

-  Components subject to wear (described in the spare part list).

 

WARRANTY FORFEITURE:

 

-  In case of delayed payment or other contractual defaults.

 

-  Whenever changes or repairs are carried out on our equipment without prior authorization.

 

-  Whenever the serial number is damaged or removed.

 

-  When the damage is caused by improper use or functioning, or if the equipment falls, is bumped  

     

   or  by other causes not due to the normal working conditions.

 

-  Whenever the unit is disassembled, tampered with or repaired without the authorization of 

  

ANEST IWATA.

 

All repair interventions carried out under warranty do not interrupt its duration.

 

All disputes will be settled in the court  of justice of Turin.

Содержание MSU-323 C

































Отзывы: