ANEP P4GU VoLTE Скачать руководство пользователя страница 7

Страница: 7 / 48

7 / 44

NT_ANEP_P3GU_07-12-2018

NT_ANEP_P4GU_VoLTE_EN_12-05-2022

7 / 48

MAIN FEATURES

• Local programming via a telephone set [DTMF]

• Remote programming via SMS

• Roaming service management (roaming)

• Control of the absence of electrical network

• Remote firmware update (with data plan)

• Checking the battery charge level

• Power failure notification SMS

• Power restored notification SMS

• Battery exhausted notification SMS

• State of the power supply under ANEP protocol

• Fallback mode: connection to the 4G network, otherwise 3G, otherwise 2G

(voice only)

• Reading of 2G, 3G or 4G signal level

• Automatic converter of selected number

• Setting transmit and receive gains

• Remote reset

• Remote firmware update (internal software)

• Mobile network intensity signaling LED

• Device status LEDs

• Line status indicator LED

• Power status indicator LED

• Dual Band Module (European 4G Network)

• Transmit power 2W

• Input for direct 12Vdc power supply

• Input for transformer power supply. external 230Vac / 12Vdc

• External antenna (cable L = 2m) / (antenna with optional 10m cord)

• Plug-in or two-wire external adapter (input 230Vac 50 Hz, output 12Vdc 500mA)

• Dimensions: 140 x 96 x 28mm

• Weight: 220g

LEDS

The P4GU VoLTE device has 4 LEDs visible on the outside. For the meaning of

the flashing of each of the LEDs, consult the chapter "Signals"

(see pages 39 to 43).

Green LED: intensity of the mobile network in 2G, 3G or 4G

Red LED: device status

White LED: line status

Blue LED: power status

Содержание P4GU VoLTE

















































Результаты поиска

Содержание P4GU VoLTE

Отзывы:

Похожие инструкции для P4GU VoLTE

Бренды по названию

Популярные бренды

ANEP P4GU VoLTE, Техническое описание

Результаты поиска

Содержание P4GU VoLTE

Отзывы:

Похожие инструкции для P4GU VoLTE

Бренды по названию

Популярные бренды