andrews ECOflo EC230/600 Скачать руководство пользователя | Manualshive

Страница: 2 / 52

background image

Reproduction of any information in this publication by any method is not permitted
unless prior written approval has been obtained from Andrews Water Heaters.

Andrews Storage Water Heaters have been designed and manufactured to comply
with current international standards of safety. In the interests of the health and safety
of personnel and the continued safe, reliable operation of the equipment, safe working
practices must be employed at all times. The attention of UK users is drawn to their
responsibilities under the Health and Safety Regulations 1993.

All installation and service on Andrews Water Heaters must be carried out by properly
qualified personnel and, therefore, no liability can be accepted for any damage or
malfunction caused as a result of intervention by unauthorised personnel.

Andrews Water Heaters’ policy is one of continuous product improvement and,
therefore, the information in this manual, whilst completely up to date at the time of
publication, may be subject to revision without prior notice.

Further information and assistance can be obtained from:

Andrews Water Heaters
Wood Lane, Erdington,
Birmingham B24 9QP

Tel: 0845 070 1055
Fax: 0845 070 1059
Email: [email protected]
Website: www.andrewswaterheaters.com

THE ANDREWS WATER HEATERS COVERED IN THIS MANUAL
ARE FOR USE WITH NATURAL GAS OR LPG (PROPANE) GAS ONLY

Copyright Andrews Water Heaters 2010

INTRODUCTION

2

ECOflo_E864_manual_SEPT2012 16/10/12 11:23 Page 2

«
1
2
3
4
...
»

Содержание ECOflo EC230/600





















































Отзывы:

Нет отзывов

Похожие инструкции для ECOflo EC230/600

Бренд: CleaverBrooks Страницы: 120

Бренд: Ideal Boilers Страницы: 8

Бренд: Crown Boiler Страницы: 23

Бренд: Sime Страницы: 40

Бренд: Henrad Страницы: 4

Logano plus GB102

Бренд: Buderus Страницы: 12

Бренд: Buderus Страницы: 168

Vitodens 100-W WB1B Series

Бренд: Viessmann Страницы: 92

Бренд: Sharp Страницы: 12

INDEPENDENT C30

Бренд: IDEAL Страницы: 72

Бренд: Keston Страницы: 4

Бренд: LAVAZZA Страницы: 43

Бренд: Rinnai Страницы: 160

Бренд: Sime Страницы: 96

Бренд: Riello Страницы: 156

Бренд: Wolf Страницы: 48

CSI 123(T) Low Nox

Бренд: Ravenheat Страницы: 4

CONCORD SUPER SERIES 4

Бренд: IDEAL Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды