andrews ECOflo EC230/600 Скачать руководство пользователя | Manualshive

Страница: 25 / 52

background image

Flue terminal

Inner wall mount
plate

4 Fixing screws
(supplied)

Hole through wall

4 Wall anchors

Flue terminal

Outer wall
mount plate

4 Fixing screws
(supplied)

Hole through wall

4 Wall anchors

Air intake openings
(must face ground)

INSTALLATION

• SECTION 3

25

FLUE SYSTEMS

INSTALLING THE HORIZONTAL
FLUE TERMINAL

NOTE:

The horizontal flue terminal supplied may be used

through outside walls up to 600mm (24in) thick.

1. Horizontal flue Terminal (Through the Wall) supplied
a) Cut an opening of at least 165mm (6.5in) diameter

through to the outside.

b) Slide the flue terminal through the wall opening to the

rib closest to the intake air openings of the terminal
and even with the outside wall.

c) Slide the outside wall plate over the flue terminal and

fasten to the wall with four screws. Depending on the
wall construction, wall anchors may be required to
reinforce the screws.

d) Install inside wall plate on the inside wall and secure

with four screws. Depending on wall construction,
wall anchors may be required to reinforce the screws.

Fig. 4

Fig. 2

ECOflo_E864_manual_SEPT2012 16/10/12 11:24 Page 25

«
...
23
24
25
26
27
...
»

Содержание ECOflo EC230/600





















































Отзывы:

Нет отзывов

Похожие инструкции для ECOflo EC230/600

VOGUE COMBI GEN2 C26

Бренд: Ideal Boilers Страницы: 80

VOGUE MAX SYSTEM 32IE

Бренд: Ideal Heating Страницы: 80

Бренд: ACV Страницы: 23

MultiTemp MR Series

Бренд: HydroTherm Страницы: 36

Бренд: ideal commercial Страницы: 28

Henrad WH 100 FF

Бренд: IDEAL Страницы: 4

Бренд: Nieco Страницы: 40

Бренд: Nieco Страницы: 28

Бренд: IDEAL Страницы: 8

Бренд: Biasi Страницы: 48

Бренд: Hoberg Страницы: 90

Бренд: Qualtex Страницы: 9

Benchmark BMK 1000

Бренд: Aerco Страницы: 178

Бренд: croydon Страницы: 2

Бренд: croydon Страницы: 2

Бренд: Baxi Страницы: 44

Бренд: Baxi Страницы: 128

Бренд: Raypak Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды