andrews ECOflo EC230/600 Скачать руководство пользователя | Manualshive

Страница: 39 / 52

background image

MAINTENANCE / SERVICE

• SECTION 6

39

INTRODUCTION

Servicing must be carried out by a properly qualified
person.

Whilst giving these instructions for the care of the ECOflo,
it is recommended that checks are carried out by the
installer or local gas service engineer at least annually.
Ensure good ventilation by keeping the heater free of
extraneous materials and clear of dust and lint. Keep
pipework, flue and tops of heaters clear of any
combustible materials. A water softener or scale inhibitor
should be employed in hard water areas. The heater
should be inspected every few months via the hand hole
cleanout and scale or silt deposits removed. Failure to do
so will shorten heater life and may invalidate the warranty.

PRE-SERVICE OPERATIONS

Before servicing, carry out the following operations.

1) Turn off the gas service cock.
2) Turn off the cold water supply to the heater.
3) Turn on the hot water draw-off taps served by the

water heater, or, for multiple installations, turn off the
hot water outlet connection valve and secondary
return valve.

4) Drain down using the drain valve on the heater.

ANNUALLY

Annual checks of the ignition systems, temperature
controls and any other controls are necessary to ensure
continued safe and efficient operation.

The entire combustion system must be sealed for this
water heater to function correctly. Ensure that the burner
access panel is kept tightly sealed. The combustion air
supply tee piece at the side of the heater must be tightly
clamped to the elbow and concentric flue adaptor.
Replace any damaged parts.

The entire exhaust flue system and combustion air supply
must be inspected at least annually for integrity of all
joints and gaskets.

GENERAL

KEEP APPLIANCE AREA CLEAR AND FREE FROM
COMBUSTIBLE MATERIALS, PETROL AND OTHER
FLAMMABLE VAPOURS AND LIQUIDS.

Water heater maintenance includes periodic tank flushing
and cleaning, and removal of lime scale. The unit should
be inspected and adjusted to maintain proper
combustion. Refer to Fig. 17 below, “Suggested
Maintenance Schedule”. A periodic inspection of the flue
installation system should be made.

MAINTENANCE / SERVICE

MAINTENANCE SCHEDULE

Following are the instructions for performing some of the recommended maintenance.
Unit inspection and adjustment should be performed by a competent qualified engineer.

COMPONENT

OPERATION

INTERVAL

REQUIRED

Tank

Sediment Removal

Every 6 months

Flushing

Relief Valve

Check Operation

Every 6 months

Proper Operation

Exhaust & Air Intake System

Inspect

Every 3 months

Joints should be sealed

Ignition System

Inspect

Annually

Clean off dust and dirt

Flue Vent Terminal

Clean Inlet Screen

As Required

Soft Brush

Flue Terminal –

Free of Shrubs

Monthly

Remove object

Horizontal or Vertical

& Debris

that caused restriction

Combustion System

Inspect

Monthly

Confirm S-OP

Condensate Waste Pipe

Inspect

Monthly

Remove restriction

CORREX POWERED ANODES

As Correx Powered Anodes are fitted as standard to this appliance, no maintenance is necessary.

ECOflo_E864_manual_SEPT2012 16/10/12 11:24 Page 39

«
...
37
38
39
40
41
...
»

Содержание ECOflo EC230/600





















































Отзывы:

Нет отзывов

Похожие инструкции для ECOflo EC230/600

Бренд: Radiant Страницы: 28

Бренд: Radiant Страницы: 24

Aerco Modulex EXT Series

Бренд: Watts Страницы: 144

Бренд: Unical Страницы: 36

Бренд: Viessmann Страницы: 52

Бренд: U.S. Boiler Company Страницы: 2

Бренд: Raypak Страницы: 2

Бренд: Ideal Boilers Страницы: 72

GENUS HE 35 Plus

Бренд: Ariston Страницы: 68

Бренд: Immergas Страницы: 4

Бренд: Gorenje Страницы: 36

Бренд: PROBOIL Страницы: 44

Бренд: Lamborghini Caloreclima Страницы: 188

Бренд: Alpha Страницы: 44

Бренд: A.O. Smith Страницы: 52

ATLAS D 32 CONDENS K130 UNIT

Бренд: Ferroli Страницы: 80

ATLAS D 25 SI UNIT

Бренд: Ferroli Страницы: 96

Бренд: HTP Страницы: 66

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды