background image

 16

Span Calibration 

3. Place the calibration weight at the center of the weighing pan and press 

the RE-ZERO key after confirming that the STABLE indicator is lit. 

  Calibration using a weight ends and the scale automatically enters 

weighing mode after displaying   

end

  .  

4. Remove the weight from the weighing pan and press the ON:OFF key to 

turn the power off and end the calibration. 

 

Setting the Gravity Acceleration 

The scale is calibrated with the gravity acceleration value 9.798 m/s

2

 at the 

factory. When the gravity acceleration at your location is different value, you 
should calibrate the scale using a calibration weight. But if the calibration 
weight cannot be prepared, change the gravity acceleration of your scale to 
the value of the area where the scale is used. See “The Value of Gravity 
Acceleration at Various Locations” of this manual. 

 

1. Press the

 

MODE key while   

Cal

      is displayed to display   

9.798 

.

 

2. Press the RE-ZERO key to make the digit to be changed blink. 

Readjust the gravity acceleration value for the scale to be used using the 
following keys. 

MODE            

To change which digit is blinking. 

RE-ZERO 

To increase by +1 the value of the blinking digit. 

3. Press the RE-ZERO key while pressing and holding the MODE key, and 

release the MODE key while keeping the RE-ZERO key depressed. The 
scale automatically enters   

Cal 

    display after displaying   

end

  . 

4. Press the ON:OFF key to turn the power off and end the operations.

 

 
 
 
 
 
 
 
 
 
 

Содержание HT-3000CL





















Отзывы: