Analytik Jena qTOWER3 84 Скачать руководство пользователя страница 39

Страница: 39 / 46

Maintenance and care

qTOWER

84 / qTOWER

84 G

Edition 02.19

11. Rotate the wheel with the installed

color modules and check whether the
color modules grind against the lid.
If this is the case, loosen the screw
connection of the color module, check
its position and retighten the screws.

NOTICE

Do not attempt to force a jammed color module into the correct position simply by tighten-

ing it further. The sensitive optics may be damaged.

12. Place the hood back onto the device.
13. First tighten the four external screws at

the upper part on the backplate of the
qTOWER³ 84.

14. Open the lid and remove the four ex-

ternal screws on the inside of the lid.

15. Close the lid again.

16. Switch on the qTOWER³ 84 Start the qPCRsoft384 program.
17. Select the command E

XTRAS



DIT

OLOR

ODULES

from the menu.

The window with the same name opens.
The available color modules are listed on the left-hand side of the window.

Содержание qTOWER3 84















































Результаты поиска

Содержание qTOWER3 84

Отзывы:

Похожие инструкции для qTOWER3 84

Бренды по названию

Популярные бренды

Analytik Jena qTOWER3 84, Руководство по эксплуатации

Результаты поиска

Содержание qTOWER3 84

Отзывы:

Похожие инструкции для qTOWER3 84

Бренды по названию

Популярные бренды