Analytik Jena qTOWER3 84 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 46

background image

Maintenance and care

qTOWER

3

84 / qTOWER

3

84 G

Edition 02.19

33



To remove reagent residue fill the affected wells with max. 20 µL distilled water

or ethanol. Wait for approx. 1 min before you suck out the liquid again. Repeat
the process until the background signal is in the normal range.

8.3

Disinfecting the device

WARNING! Biological hazard!

Clean the qTOWER

3

84 with particular care after analyzing potentially infectious material.

Wear suitable protective equipment, e.g. protective gloves.

NOTICE

The only suitable cleaning method for the housing is wipe disinfection.
When using spray disinfectants there is a risk that the liquid enters the sensitive electronic

system through the air vents. If the disinfectant has a spray nozzle, apply disinfectant to a

suitable cloth before using it on the device.



Avoid contamination by handling sample substances with care.



Wipe spilled samples or reagents immediately with an absorbent cloth or piece

of paper.



If the qTOWER³ 84 is used for the analysis of infectious material, great care

must be taken because the qTOWER³ 84 cannot be decontaminated as a whole
device.



Immediately remove visible contamination by suitable means. Do not allow sol-

vents to enter the device.



The sample block is also suitable for wipe and spray disinfection The only suit-

able cleaning method for the housing is wipe disinfection.

Device part

recommended disinfect-
ants

Provider

Sample
chamber

Descosept AF
Meliseptol HBV (cloths)

Dr. Schuhmacher GmbH
B. Braun company

Housing

Descosept Spezial

Dr. Schuhmacher GmbH

Pay attention to the efficacy spectrum of the listed disinfectants with regard to your cus-
tomer-specific decontamination requirements!



Only the use of ethanol or isopropanol containing disinfection agents is ap-

proved for wipe disinfection. The use of disinfection agents with ingredients or
concentrations that differ from the recommended disinfection agents invalidates
all warranty claims regarding damage to the device or non-effectiveness.



If the qTOWER

3

84 has to be sent to Analytik Jena AG for service, a prior de-

contamination must be carried out and documented (see "Return" p. 41).

«
...
33
34
35
36
37
...
»

Содержание qTOWER3 84















































Отзывы:

Нет отзывов

Похожие инструкции для qTOWER3 84

Бренд: Kawai Страницы: 10

Бренд: unios Страницы: 2

Бренд: Madrigal Страницы: 5

Бренд: MacDon Страницы: 504

Бренд: TEC Страницы: 6

Бренд: U Technology Страницы: 6

Бренд: UNI-T Страницы: 4

UPO3000E Series

Бренд: UNI-T Страницы: 94

Бренд: Underhill Страницы: 12

Бренд: UMS Страницы: 92

Бренд: Xtool Страницы: 8

Бренд: H&S Страницы: 32

Бренд: Dantel Страницы: 22

Бренд: B&G Страницы: 2

Бренд: Össur Страницы: 82

Novation Launchkey Mini

Бренд: Focusrite Audio Engineering Страницы: 36

Бренд: Vitax Страницы: 12

Бренд: SAC Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды