AMX Precis HT Скачать руководство пользователя | Manualshive

Страница: 21 / 65

background image

Installation & Setup

15

Precis HT Instruction Manual

Rack Installation & System Setup

The Precis HT Distribution Matrix enclosure can be mounted in a standard EIA 19 in. (48.26 cm) rack
(rack ears are provided).

Important:

The system requires one empty rack unit above and below the enclosure to allow

adequate airflow; three empty rack units are recommended

.

Required items for rack installation:

Enclosure

Standard EIA 19 in. (48.26 cm) rack

Rack ears (with 8 screws per set)

Screwdriver

Screws that fit your rack for mounting the enclosure

Power cord

Optional items for rack installation:

Surge-protector(s) – highly recommended

A laptop computer or PC with a null modem cable
(for communication with the Precis HT via the CONTROL port)

Installation Recommendations

Write the system’s serial number in an easily accessible location before installing the
Precis

HT in a rack. The system’s serial number is located in two places on the enclosure; on

the left rear and on the left side of the enclosure (near the power receptacle).

Use earth-grounded power cords / system with the Precis HT.

Attach all power cords to a single surge protector and/or an AC line conditioner.

Apply power to the Precis HT enclosure before applying power to its source and destination
devices.

«
...
19
20
21
22
23
...
»

Содержание Precis HT


































































Отзывы:

Нет отзывов

Похожие инструкции для Precis HT

Бренд: Quick Страницы: 28

PARAGON II Series

Бренд: Raritan Страницы: 1

Paragon Manager

Бренд: Raritan Страницы: 117

Бренд: Siqura Страницы: 2

Бренд: Holland Страницы: 4

VNLW-P-1001-MV-N-V

Бренд: Greengate Страницы: 2

HD Flash 4 KD-SW4x1

Бренд: Key Digital Страницы: 12

ET2-0602-M Series

Бренд: Leonton Страницы: 17

Бренд: König Страницы: 8

Бренд: PhD Solutions Страницы: 23

Бренд: Grizzly Страницы: 2

MISCOM7028GX Series

Бренд: Maiwe Страницы: 22

Бренд: Linksys Страницы: 4

Smart MatriX LE

Бренд: Analog way Страницы: 56

ConferX AC-CX84-AUHD

Бренд: AVPro Edge Страницы: 6

Бренд: Zigen Страницы: 72

NIVOMAG MK-21 Series

Бренд: NIVELCO Страницы: 2

Бренд: Uniclass Страницы: 33

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды