manualshive.com logo in svg

AMX Precis HT, Инструкция по эксплуатации

Поделиться
Скачать
AMX Precis HT Скачать руководство пользователя страница 41

Control Panel Operation

35

Precis HT Instruction Manual

Control Panel Operation 

Overview

All Precis HT systems have an integral Precis X/Y Control Panel for controlling the system’s switches 
and system attributes. The control panel can also be used for system verification, redundant control, and 
troubleshooting. 

FIG. 20 illustrates a 12x8 Precis HT Control Panel. Other models may vary slightly in appearance.

Note:

 

AMX AutoPatch software can also be used to control a system; for more information, see 

the “AMX AutoPatch CD”. In addition, AMX AutoPatch enclosures can be controlled using BCS 
(Basic Control Structure) commands transmitted through an external controller; see the
“BCS Protocol Instruction Manual” on the CD or at 

www.amx.com

.

Modes of Operation

A Precis HT Control Panel works in three standard modes: 

 

Switch (default) – use to execute switches

 

Status – use to verify signal status

 

Macro – use to execute a macro (a local preset pre-defined in XNConnect)

Virtual Matrices (Levels)

Precis HT models execute switches on four levels (virtual matrices):

 

VM 0 (All VMs)

 

VM 1 (video)

 

VM 2 (digital audio)

 

VM 3 (stereo audio)

FIG. 20  

 12x8 control panel with digital volume control

Содержание Precis HT


































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды