AMS TOUCHLESS Скачать руководство пользователя страница 37

Страница: 37 / 50

L0192A

MACHINE TROUBLESHOOTING CHART

IF A REPLACEMENT PART IS NECESSARY, PLEASE CONTACT YOUR DISTRIBUTOR

The following troubleshooting chart may be used to find quick remedies for electrical and mechanical failures in the
vendor.

Symptom

Possible Cause

Remedy

No power at the control board. (no
beeping sound during power-up or

when the service mode button is

pushed).

No power from power cord.

Check power cord, outlet or supply.

Check for tripped GFCI.

3.0 amp fuse is blown.

Replace 3.0 amp fuse.

Fuse harness is not connected to the

back of the fuse holder.

Connect fuse holder harness.

Short or cut in the power harness

between the transformer and control

board.

Check continuity through the power

harness. If there is no continuity

replace the power harness.

Transformer does not have power at

the 24 VAC secondary side.

Insure primary side of transformer is

receiving 120VAC power. If there is not

at least 29 VAC on secondary side

replace transformer.

Phone displays “Vend Failed” With

Control Box Open, the AMS Display

shows “Please Make Another Selec-

tion”.

Selection not configured in the motor

matrix.

Reconfigure the motors. Check for

appropriate motor coupling.

Motor jammed.

Clear jammed motor and clear error

code.

Vend not sensed by sensor.

Clear fault in sensor boards or harness:

possible control board error.

Tray selections do not make a

complete cycle with S2-H motors.

Harness off at the J-1, J-5 and/or J-6

connector on the control board.

Motor jammed.

Sensors blocked.

Connect harness to the control board

connector.

Check harnesses.

Tray selection continues to turn after a

successful vend.

Wrong motor or motor type: S2 motors

will not stop at Home position.

See

MOTOR TYPE

pg. 22.

TROUBLESHOOTING

Содержание TOUCHLESS



















































Результаты поиска

Содержание TOUCHLESS

Отзывы:

Похожие инструкции для TOUCHLESS

Бренды по названию

Популярные бренды

AMS TOUCHLESS, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание TOUCHLESS

Отзывы:

Похожие инструкции для TOUCHLESS

Бренды по названию

Популярные бренды