L0086, Rev. G
AMS SENSIT 3 GLASS FRONT VRM
8-4
7. After testing, remount the temperature sensor on the two
spring clips, and carefully re-wrap the sensor wire in the
two bracket slots ensuring the wire is not caught or
pulled, and is not pinched when the door is closed.
8. Close merchandiser door. The merchandiser will return
to normal operation (including a cool-down time if
needed).
8.11 UTILITY LOADING INSTRUCTIONS
Utility loading instructions are not available at this
time. Refer to Section 8.1 for loading of software.
8.12 GFCI TEST
1. If the power is on in the merchandiser, test the GFCI as
follows: press the TEST pushbutton on the GFCI for 1
second to trip the GFCI and shut it off. The
merchandiser power should turn off. Then press the
RESET pushbutton for 1 second to return the GFCI to
normal operation. The merchandiser should turn on.
2. If the power is not on in the merchandiser check the
GFCI as follows: even if the GFCI is off, press the TEST
pushbutton on the GFCI for 1 second to trip the GFCI
and shut it off. Then press the RESET pushbutton for 1
second to return the GFCI to normal operation. The
merchandiser should turn on.
3. If the GFCI can be reset but there is no power, check
the power outlet at the wall.
4. If the GFCI will not stay on after RESET is pressed
there is a short circuit in the merchandiser. Unplug the
merchandiser. Follow the suggestions in Section 7.5 to
determine the cause of the short circuit, and correct it.
8.13 REPLACING THE POWER CORD
Use this procedure to remove a power cord that is cut,
split open or is otherwise damaged or a hazard. A ¼”
nut driver, needle nose pliers, gloves and protective
eyewear are required.
Save all hardware and fasteners for re-use.
1. Remove power from the vendor by removing the
power plug from the wall outlet. Move the vendor
away from wall in order to reach the back.
2. Open vendor door. Separate the power cord from
the rest of the vendor electrical harness by using
the quick disconnect.
3. Remove screws attaching the wire bushing plate
from inside rear wall of cabinet.
4. Remove wire bushing and power cord from the
plate.
5. Outside of cabinet, remove the two screws
attaching back grommet plate to cabinet.
6. Slide grommet plate down and away from slot in
molded-on grommet on power cord.
7. Remove power cord down and away from round
cut-out in back of cabinet.
8. Remove the damaged power cord from the
cabinet and discard it.
9. Insert the new power cord end with the quick
disconnect into the power cord hole. Do not plug in
the new power cord at this time.
10. Slide the groove of the molded-on grommet on the
power cord up onto the round cut-out in back of
cabinet.
11. Slide the grommet plate up into lower half of
molded-on grommet, making sure it slides up
behind the cut-out in the cabinet. The power cord
should come out of the grommet and be facing
down.
12. Position protective cover over grommet plate.
13. Insert and tighten 2 screws.
14. Inside the cabinet, install the wire bushing and
power cord onto the wire bushing plate.
15. Reinstall the plate to the inside rear wall of the
cabinet
16. Reconnect the power cord quick disconnect inside
the cabinet.
17. Plug the power cord into the power outlet. The
power should come on in the vendor.
18. Test the GFCI on the power cord (Refer to Section
8.12).
19. If everything is operational return the
merchandiser to its position next to the wall.
8-14. STORING THE MERCHANDISER
If the merchandiser is to be stored without power for
several days or longer, use the following instructions.
These instructions are similar to those used to store any
refrigerator.
1. Remove any products from the merchandiser.
2. Unplug the merchandiser from the power outlet.
3. Clean the inside using the general directions given in
Section 8-5.
4. Leave the door open for a day to allow the interior to
thoroughly dry.
5. Close the door and lock it to protect the interior.
6. Roll up the power cord and place it in the hopper.
7. If the merchandiser is being moved follow the handling
and setup procedures given in Section 4.
Содержание Sensit 3 39 VRM
