AMS SENSIT 3 GLASS FRONT VENDOR
L0086, Rev. G
6-3
2-JOG TRAY
– All motor positions on the
selected tray will be tested. The display will
show the number of the motor being jogged, or
it will show a message that a motor is missing.
3-CHECK JAMMED
– The control will attempt
to run each motor that has caused a jammed
motor error. The status of the motor will be
displayed afterward.
6.7.2 Link
Motors
The user can link adjacent selections of the
same product on the same tray. The leftmost
linked selection is the master selection. All other
linked selections are vended using the selection
number and price of the master selection. Linked
selections are vended sequentially for better
product rotation. Entering the selection number of
any linked selection will default to the master
selection number, and the control will vend the
next linked selection in the sequence.
1.
NEW LINK
– Enter the tray where the motors
are to be linked, then enter the first and last
column numbers (left to right) to be linked.
2.
VIEW / EDIT
– The user can view, change, or
delete existing links.
3.
CLEAR ALL
– This will delete all current links.
The prices of the previously linked selections
will remain the same as their master selections
until new prices are set.
6.7.3 Motor
Type
Motor Type allows the user to change the
motor stop and credit deduction behavior. See the
table below for more details on the various
settings available under this function.
MOTOR TYPES
ITEM
DISPLAYED OPTION NAME
MOTOR
STOP
CREDIT
DEDUCTION
1 SENSIT
Sensor* Sensor
2 HOME/SENSOR/3
Home
Sensor
3
HOME//3
(FACTORY DEFAULT)
Home + Extra**
Sensor
4 HOME_ONLY/3
Home
Home
SII WITH HOMING MOTOR TYPES
5***
HOME/SENSOR/2
Sensor
Sensor
6***
HOME//2
Home + Extra**
Sensor
7***
HOME_ONLY/2
Home
Home
* If S3 motors are used: the switch function is ignored.
** "Extra" means that if a drop is not detected by the home position, the motor will move additional
increments to try to vend the product.
*** These are settings for use only with merchandisers equipped with Sensit II with Homing.
6.7.4 Delayed
Stop
The user can program a delayed stop of up
to one second to allow a motor to continue running
after the product has been dispensed.
1. ENTER SELECTION
– Enter the number of
the selection to be delayed, enter
9
to edit,
then enter the time in tenths of a second. The
decimal point is placed automatically.
Example: Entering
8
will program a delay
of 0.8 seconds.
The user can save the programmed
delay to the selection, the entire tray, or all
selections in the merchandiser. Linked
selections will use the delay programmed for
the master selection.
6.7.5 Letter / Number
The control board/software default is for
NUMERIC, using the 12-key keypad. Note that if
the control board is changed this setting may need
to be set to “Number”. This setting should be
changed to “Letter” if the merchandiser is
equipped with 20 pushbutton keypads (with
alphabetic characters). Depending on the setting,
the top tray is designated “1” or “A”, and
downward with numbers (2-8) or letters (B-H).
6.7.6 Configure
Motors
Configure Motors moves each switched
motor to the home position (moving the motor only
Содержание Sensit 3 39 VRM
