AMGO HS-12 Скачать руководство пользователя страница 34

Страница: 34 / 40

Every six months:

Make a visual inspection of all moving parts for possible wear, interference or
damage.

Check and adjust as necessary, equalizer tension of the cables to insure level lifting.

Check columns for plumbness.

Check rubber pads and replace as necessary.

Check safety device and make sure proper condition.

VIII. TROUBLE SHOOTING

TROUBLE

CAUSE

REMEDY

Motor does not

run

1. Button does not work

2. Wiring connections are not in good

condition

3. Motor burned out

4. Height Limit Switch is damaged

5. AC Contactor burned out

1. Replace button

2.Repair all wiring connections

3. Repair or replace motor

4.Replace the Limit Switch

5. Replace AC Contactor

Motor runs but

the lift is not

raised

1. Motor runs in reverse rotation

2. Gear Pump out of operation

3. Release Valve in damage

4. Relief Valve or Check Valve in damage

5. Low oil level

1.Reverse two power wire

2.Repair or replace

3. Repair or replace

4.Repair or replace

5.Fill tank

Lift does not

stay up

1. Release Valve out of work

2. Relief Valve or Check Valve leakage

3. Cylinder or Fittings leaks

Repair or replace

Lift raises

slowly

1. Oil line is jammed

2. Motor running on low voltage

3. Oil mixed with Air

4. Gear Pump leaks

5. Overload lifting

1. Clean the oil line

2. Check electrical system

3. Fill tank

4. Replace Pump

5. Check load

Lift can not

lower

1. Safety device are locking

2. Release valve in damage

3. Safety cable broken

4. Oil system is jammed

5. Hydraulic Solenoid valve does not work.

1. Release the safeties

2. Repair or replace

3. Replace

4. Clean the oil system

5. Replace

Содержание HS-12









































Результаты поиска

Содержание HS-12

Отзывы:

Похожие инструкции для HS-12

Бренды по названию

Популярные бренды

AMGO HS-12, Инструкция по установке и обслуживанию

Результаты поиска

Содержание HS-12

Отзывы:

Похожие инструкции для HS-12

Бренды по названию

Популярные бренды