AMGO HS-12 Скачать руководство пользователя страница 33

Страница: 33 / 40

VI. OPERATION INSTRUCTIONS

Please read the safety tips carefully before operating the lift
To lift vehicle

Keep clean of site around the lift.

Position lifting arms to the lowest position.

Shorten the arms to the shortest condition.

Open the lifting arms to allow vehicle driving in.

Position vehicle between columns.

Move/adjust 4 arms so that lifting pads are under correct lift points (per
manufacturer’s recommendation) of vehicle. Adjust pads so that all four pads will

contact the lift points simultaneously. This ensures the vehicle will be lifted in a
level position.

Push button

“UP”

until the lift pads contact underside of vehicle totally. Recheck to

make sure vehicle is secure;

Continue to raise the lift slowly to the desired working height, ensuring the balance
of vehicle;

Push button “

DOWN”

to lower lift onto the nearest safety. The vehicle is ready to

repair.

To lower vehicle

Be sure clear of around and under the lift, only leaving operator in lift area;

Push button

“UP”

to raise the vehicle slightly, and then release the safety device,

lower vehicle by pushing lowering handle.

Position the arms to the shortest length and then open the them.

Drive away the vehicle.

Turn off the power.

VII. MAINTENANCE SCHEDULE
Monthly:

Re-torque the anchor bolts to

150.m;

Check all connectors, bolts and pins to insure proper mounting;

Lubricate cable with lubricant;

Make a visual inspection of all hydraulic hoses/lines for possible wear or leakage;

Check safety device and make sure proper condition;

Lubricate all rollers and pins with 90wt. Gear oil or equivalent;

Note: All anchor bolts should take full torque. If any of the bolts does not function for

any reason, DO NOT use the lift until the bolt has been replaced.

Содержание HS-12









































Результаты поиска

Содержание HS-12

Отзывы:

Похожие инструкции для HS-12

Бренды по названию

Популярные бренды

AMGO HS-12, Инструкция по установке и обслуживанию

Результаты поиска

Содержание HS-12

Отзывы:

Похожие инструкции для HS-12

Бренды по названию

Популярные бренды