AMGO 209X Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 30

AMGO 209X Скачать руководство пользователя страница 23

21

You can adjust the lower speed of the lift if needing: Loosen the Fixing Nut of the

throttle valve, and then turn the throttle valve clockwise to decrease the lower speed,

or counterclockwise to increase the lower speed. Do not forget to tighten the fixing

nut after the lower speed adjustment has been done.

4.

Test with load

After finishing the above adjustment, test running the lift with load. Run the lift in

low position for several times first, make sure the lift can rise and lower

synchronously, the Safety Device can lock and release synchronously. And then test

run the lift to the top completely. If there is anything improper, repeat the above

adjustment.

NOTE: It may be vibrated when lifting at start, please lifting it with load for several
times, the air would be bled and the vibration would be disappeared automatically.

VI. OPERATION INSTRUCTIONS

Fig. 33

Fixing nut

Throttle valve

Fixing nut

Throttle valve

Adjust clockwise, slow down to decent

Counter clockwise, faster descent

Hydraulic System

Fig. 34

«
...
21
22
23
24
25
...
»

Содержание 209X































Отзывы:

Нет отзывов