AMF REECE S-311, Руководство по эксплуатации и ремонту, Страница: 16 / 142

S-311
1-4
Released:01/2014
E-mail: service@amfreece.cz; webside: amfreece.com
Phone: +420 582 309 146; Fax: +420 582 360 606
A - INTRODUCTION
4. SPECIFICATION
S-311 Elektronic buttonhole machine with chain stitch is possible to use for men`s and women`s wear.
Possible to use gimp thread, not in round eye.
* Note:
If a customer uses thread size 100 and less, the manufacturer recommends to use the left looper 17.0069.4.019
If you use poor quality threads on the machine, the thread can burn at the needle (producer recommend decrease
machine´s speed).
** Gimp 10 - 30 → CT Throat Plate 10.4012.5.016
30 - 100 → CT Throat Plate 10.4012.1.016
10.4012.2.014
Machine type/model
AF
10 to 50 mm
3,0 - 20,0 mm
4 to 8 mm
4 to 20
4 to 20
12 mm
in 8,0 mm
Cut before (CB), cut after (CA), no cut (OFF)
- 0,50 to + 1,2 mm
See section D 3.3
4 to 6 mm
0,5 to 1,5 mm
No eye; 2,2 x 3,0 mm; 2,8 x 4,2 mm; 3,0 x 4,6 mm; 3,2 x 5,0 mm; 3,4 x 4,2 mm
2,1 mm (AF, LTT); 2,3 mm (CT) ( ± 0,3 mm electronic); 2,7 mm (± 0,3 mm electronic)
2,1 mm (AF, LTT); 2,3 mm (CT) ( ± 0,5 mm electronic); 2,7 mm (± 0,5 mm electronic)
± 1,5 mm
64 mm
02.0558.0.111 (Nm 100)
02.0558.1.112 (Nm 110)
80, 100, 120, gimp size 10-30 standard **
80, 100, 120, gimp size 30-100
L = 14 to 24mm
L+L = 21 to 31mm
1
0,55 MPa = 80 PSI
530 mm (height) x 370 mm (width) x 560 mm (depth)
730 mm (height) x 1100 mm (width) x 700 mm depth) + 150 mm distance
64 kg
175 kg
1NPE~60Hz 230 V/TN/S; 1NPE~50Hz 230 V/TN/S
Min. 10A Characteristic C (EN60947-2)
L =86,9db; L =74,8 db; Noise measurement according to EN ISO 3746:1995
wA pfA
L = 22 to 32mm
L+L
1
= 29 to 39mm
according to IEC 364-3, IEC 364-5-51 temperature from +5°C to 40°C, relative air humidity from 30 to 80%
14 to 24mm 22 to 32mm
1000 to 2000 stitches/min (500 to 1000 rev/min of the drive shaft)
0,5 to 2,0 mm (increments of 0,1 mm)
Sewing speed
Stitch Density
Buttonhole style
Eye type
Flybar length
Length of the cross bar
Number of stitches in the eye
Number of stitches in the round end
Clamp foot height (max)
Maximum work thickness
Buttonhole Cutting Mode
Cutting Space
Cut position (Y axis)
Bedplate movement
Needle system
Recommended threads*
Upper thread trimming
Lower thread and gimp trimming
Cutting space
Operating Condition
Air pressure
Machine db Level
Machine Head Dimension
Machine Head Weight
Table Dimensions
Machine Weight
Electrical requirements
Line Circuit Breaker
Bite Range Elecctronic
Bite Range Elecctronic (???)
The length
of hole
CT 14 - 24 mm
CT 22 - 32mm
L = 3 to 7 mm
(Short ends)
max 3,5 mm
0,5 to 1,5 mm
Cross bar density