background image

About AMETEK 

AMETEK Programmable Power, Inc., a Division of AMETEK, Inc., is a global leader in the design 
and manufacture of precision, programmable power supplies for R&D, test and measurement, 

process control, power bus simulation and power conditioning applications across diverse 

industrial segments.  From bench top supplies to rack-mounted industrial power subsystems, 

AMETEK Programmable Power is the proud manufacturer of Elgar, Sorensen, California 

Instruments and Power Ten brand power supplies. 
AMETEK, Inc. is a leading global manufacturer of electronic instruments and electromechanical 
devices with annualized sales of $2.5 billion. The Company has over 11,000 colleagues working   

at more than 80 manufacturing facilities and more than 80 sales and service centers in the United 

States and around the world. 

Trademarks 

AMETEK is a registered trademark of AMETEK, Inc. Sorensen is a trademark owned by AMETEK, 

Inc. Other trademarks, registered trademarks, and product names are the property of their 

respective owners and are used herein for identification purposes only. 

Notice of Copyright 
HPD Series Programmable DC Power Supply Operation Manual 

© 2007 AMETEK Programmable 

Power, Inc. All rights reserved. 

Exclusion for Documentation 

UNLESS SPECIFICALLY AGREED TO IN WRITING, AMETEK PROGRAMMABLE POWER, INC. 

(“AMETEK”): 
(a)

 

MAKES NO WARRANTY AS TO THE ACCURACY, SUFFICIENCY OR SUITABILITY OF ANY 

TECHNICAL OR OTHER INFORMATION PROVIDED IN ITS MANUALS OR OTHER 

DOCUMENTATION. 

(b)

 

ASSUMES NO RESPONSIBILITY OR LIABILITY FOR LOSSES, DAMAGES, COSTS OR 

EXPENSES, WHETHER SPECIAL, DIRECT, INDIRECT, CONSEQUENTIAL OR INCIDENTAL, 

WHICH MIGHT ARISE OUT OF THE USE OF SUCH INFORMATION. THE USE OF ANY SUCH 

INFORMATION WILL BE ENTIRELY AT THE USER’S RISK, AND 

(c)

 

REMINDS YOU THAT IF THIS MANUAL IS IN ANY LANGUAGE OTHER THAN ENGLISH, 

ALTHOUGH STEPS HAVE BEEN TAKEN TO MAINTAIN THE ACCURACY OF THE 
TRANSLATION, THE ACCURACY CANNOT BE GUARANTEED. APPROVED AMETEK CONTENT 

IS CONTAINED WITH THE ENGLISH LANGUAGE VERSION, WHICH IS POSTED AT 

WWW.PROGRAMMABLEPOWER.COM. 

Date and Revision 

July 2014 Revision E 

Part Number 

TM-30OP-01XN 

Contact Information 

Telephone:  800 733 5427 (toll free in North America) 

858 450 0085 (direct) 

Fax: 

858 458 0267 

Email: [email protected] 

[email protected] 

Web: www.programmablepower.com 

 

 

 

 

 

Содержание sorensen hpd series










































Отзывы: