American Panel AP20BCF200-3-XL Скачать руководство пользователя

Страница: 7 / 36

5800 SE 78th St. Ocala, FL 34472

AP20BCF200-3-XL Installation & Operations Manual

P: (800) 327-3015

Cam-Lock Operation

The cam-lock locking device is located in the perimeter edge of all panels. Cam-Lock access holes are located on the

interior side of the panels. Generally speaking the male locks are located on the right side, top and bottom of the wall

panels.

The cam action of the lock will pull the panels together, compressing the factory applied gasket and providing an air

tight seal.

To operate the cam-lock, (as shown) insert the

panel lock wrench (located in the accessory box)

through the lock access hole and into the hex

opening in the male cam-lock.

Turn the panel lock wrench counter clockwise

to check that the locking arm is brought to a

completely open position.

Next, rotate the panel lock wrench clockwise 3/4 of

a full turn to actuate the lock engaging the locking

arm to the lock pin. The cam action of the lock will

pull the panels together, compressing the factory

applied gaskets and providing an air tight seal.

Finally, rotate the panel lock wrench approximately

1/4 turn to fully actuate the lock by securing the

cam-lock arm to the pin. Once all the cam-locks

are engaged, the access holes must be plugged

with the supplied lock hole buttons (located in the

accessory box).

Male and female cam-lock mechanisms must line-up on adjacent panels, but are able to tolerate a +/- 1/8” tolerance.

Continually check to see that the tops of the adjacent panels are evenly lined up and flush before locking.

Continually check to see that the interior seam of the panels being locked together is flush, tolerance is +/- 1/64”.

Tools Needed

Have these tools available for the installation of the AP20BCF200-3-XL.

5/16” Cam lock wrench (included in accessory box)
Tape measure
Adjustable wrench or
Refrigerant oil
Insulation tape
Sockets :

•  9/16” standard and deep well
•  7/16”
•  11/32”

Phillip head bit
Drill driver
1 1/4” hole saw for stainless steel
Level
Leak sniffer or soapy solution

Содержание AP20BCF200-3-XL





































Результаты поиска

Содержание AP20BCF200-3-XL

Отзывы:

Похожие инструкции для AP20BCF200-3-XL

Бренды по названию

Популярные бренды

American Panel AP20BCF200-3-XL, Инструкция по установке и эксплуатации

Результаты поиска

Содержание AP20BCF200-3-XL

Отзывы:

Похожие инструкции для AP20BCF200-3-XL

Бренды по названию

Популярные бренды