American Hometec AHG-T42-LP Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 48

American Hometec AHG-T42-LP Скачать руководство пользователя страница 3

Page 3

INTRODUCTION AND SAFETY WARNINGS

INTRODUCTION

Thank you for purchasing an American Hometec

™

Gas Tankless Water Heater. In

order to ensure proper installation, safe operation, and long life, please carefully read
these instructions. Installation should only be completed by licensed professionals.
The

use of professionals ensures the installation is in full

compliance with all

required building, plumbing and electrical codes.

KEEP THIS MANUAL for future reference. This booklet includes useful information

about the product, maintenance requirements and the details of your product

warranty.

IMPORTANT SAFETY INSTRUCTIONS

READ AND FOLLOW ALL INSTRUCTIONS.

When using this equipment, basic precautions should always be followed.

Safety Definitions

This symbol is the safety alert symbol which is used to alert you to potential hazards
that can kill or hurt you and/or others.

Indicates an imminently hazardous situation which if
not avoided will result in death or serious injury.

Indicates a potentially hazardous situation which if
not avoided could result in death or serious injury.

Indicates a potentially hazardous situation which if
not avoided could result in minor or moderate
injury. It may also be used to alert against unsafe
practices.

«
1
2
3
4
5
...
»

Содержание AHG-T42-LP

















































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды