American Dynamics RAS915LS Скачать руководство пользователя страница 74

Страница: 74 / 124

Command Summary

The following table lists the commands to operate the configuration utility when the dome is installed
in a SensorNet or RS-422 environment.

If you want to …

Use …

Start

the configuration utility.

Press and hold

Iris Open,

press

and hold a

Focus button,

then

press

Zoom Out*

Move the

highlight bar

on the active menu.

Pan/Tilt

Select

the highlighted item on the active menu.

Focus

Increase

the value of the selected setting. For example, Red or

Blue white balance values.

Zoom In

Decrease

the value of the selected field. For example, Red or

Blue white balance values.

Zoom Out

Display the

next choice

for the setting. For example,

Maximum Zoom setting.

Zoom In

Display the

previous choice

for the setting. For example,

Maximum Zoom setting.

Zoom Out

Save changes and exit

the utility from any screen.

Iris Close,

then

Focus*

Manually activate or deactivate

IR mode

Press and hold

Iris Open,

press

and hold

Focus Far,

then press

Focus Near*

These commands not supported with MPLT with ADCC0200 or ADCC0300 controller. Refer to the appropriate
operator’s manual for instructions.

Setting Names / Working with Passwords

When setting names or entering password information, the screen displays the available characters in
the selected languages. In these situations, the following commands are used:

If you want to …

Use …

Move the

highlight left or right

in the character field.

Pan

Move the

highlight up or down

in the character field.

Tilt

Select

the highlighted character in the character field.

Focus

Move the cursor to the

right

of the current character

in the

name or password.

Zoom In

Move the cursor to the

left

of the current character

in the

name.

Zoom Out

A–2

SpeedDome Ultra VII Operator's Manual

Содержание RAS915LS





























































































































Результаты поиска

Содержание RAS915LS

Отзывы:

Похожие инструкции для RAS915LS

Бренды по названию

Популярные бренды

American Dynamics RAS915LS, Руководство оператора

Результаты поиска

Содержание RAS915LS

Отзывы:

Похожие инструкции для RAS915LS

Бренды по названию

Популярные бренды