American Dynamics RAS915LS Скачать руководство пользователя страница 42

Страница: 42 / 124

Note:

When areas are programmed, each area is assigned a default name. Instructions

for assigning new names appear in

Chapter 5

To program areas, select

Area Boundaries

from the

Alarms/Areas/Home/Presets/PZ

screen.

The following screen appears:

AREA BOUNDARIES

PAN to start of BOUND 1-16

PAN RIGHT ONLY

ZOOM to mark BOUNDARY
FOCUS saves and exits

If no boundary is set, pressing

Focus

quits without making any changes.

The dome supports from 2 to 16 areas.

I M P O R T A N T

If areas were previously programmed, you cannot restore the previously programmed
boundaries by selecting

Quit Without Saving

from the

Dome Configuration Menu

once you begin making changes to the boundaries.

Setting Area Boundaries

1. Select

Alarms/Areas/Home/Presets/PZ

from the

Dome Configuration Menu

2. Move the highlight bar to

Area Boundaries

, then select.

The

Area Boundaries

screen appears.

3. Adjust the camera to the starting point of the first area, and press

Zoom

to mark the boundary.

4. Adjust the dome to the right until the ending point of the area is seen. If you attempt to move left,

an error message appears. See the note on page 4–11 for information.

5. Mark the end-point of the area.

The area number automatically advances.

6. Repeat steps 4 and 5 for each area you want to establish.

4–10

SpeedDome Ultra VII Operator's Manual

Содержание RAS915LS





























































































































Результаты поиска

Содержание RAS915LS

Отзывы:

Бренды по названию

Популярные бренды

American Dynamics RAS915LS, Руководство оператора

Результаты поиска

Содержание RAS915LS

Отзывы:

Бренды по названию

Популярные бренды