American Dynamics RAS915LS Скачать руководство пользователя страница 93

Страница: 93 / 124

5. Use the joystick to move the highlight to

Presets

. Press

Set

to select. The

Select Preset to

Program

screen displays.

SELECT PRESET TO PROGRAM

PRESET

NUMBER PRESET

NAME

1-64 PRESET

1-64

FOCUS FAR to program preset

EXIT

6. Use the joystick to select the Preset you want to program. If the Preset has been programmed the

dome automatically moves to that position.

•

Move the joystick right to increase the preset number.

•

Move the joystick left to decrease the preset number.

When the correct Preset number appears, press

Set

to begin programming.

7. The

Presets

screen displays. Use the joystick to adjust the dome to the correct pan/tilt position.

PRESETS

PRESET X

Position camera with PAN

TILT, ZOOM and IRIS

FOCUS FAR to save and exit

EXIT

IMPORTANT!

If using the WV-CU550A Controller with the WJ-SX550 Multiplexer, you must

press

F3 (A. Res)

to adjust the zoom, focus, or iris settings. This places the controller in normal

navigating mode. Make the necessary adjustments. When finished, press

F1 (On)

to resume

menu mode.

8. Press

Set

to save the Preset information.

9. To program more Presets, repeat steps 5 through 8. To exit the Dome Configuration Menu and

save changes, press

F4 (Exit)

To verify the Preset programming, enter a Preset number (1-64) and press

Preset

Tested Panasonic Equipment

The following Panasonic equipment has been tested with SpeedDome Ultra VII:

•

WJ-SX550 Multiplexer

•

WV-CU550A Controller

Panasonic Up-the-Coax (UTC) Protocol Command Summary

D–5

Содержание RAS915LS





























































































































Результаты поиска

Содержание RAS915LS

Отзывы:

Бренды по названию

Популярные бренды

American Dynamics RAS915LS, Руководство оператора

Результаты поиска

Содержание RAS915LS

Отзывы:

Бренды по названию

Популярные бренды