American Dryer Corp. ML-190 Скачать руководство пользователя страница 4

Страница: 4 / 62

IMPORTANT

PLEASE OBSERVE ALL SAFETY PRECAUTIONS displayed on the equipment and/or
specified in the installation manual included with the dryer.

Dryer

must not be

installed or stored in an area where it

will

exposed to water or weather.

The wiring diagram for the dryer is located in the front electrical control box area.

IMPORTANT

Dryer

must be

installed in a location/environment, which the ambient temperature

remains between 40° F (4.44° C) and 130° F (54.44° C)

FOR YOUR SAFETY

DO NOT

DRY MOP HEADS IN THE DRYER.

DO NOT

USE DRYER IN THE PRESENCE OF DRY CLEANING FUMES.

WARNING

UNDER NO CIRCUMSTANCES should the dryer door switches, the lint drawer switch,
or the heat safety circuit ever be disabled.

Do not modify this appliance.

The dryer

must never be

operated with any of the back guards, outer tops, or service

panels removed. PERSONAL INJURY OR FIRE COULD RESULT.

DRYER

MUST

NEVER

OPERATED WITHOUT THE LINT FILTER/SCREEN IN

PLACE, EVEN IF AN EXTERNAL LINT COLLECTION SYSTEM IS USED.

If a hi-limit switch trips (burner or exhaust), a service call is required to investigate
the reason and resolve the issue.

Содержание ML-190































































Результаты поиска

Содержание ML-190

Отзывы:

Бренды по названию

Популярные бренды

American Dryer Corp. ML-190, Руководство по установке

Результаты поиска

Содержание ML-190

Отзывы:

Бренды по названию

Популярные бренды