manualshive.com logo in svg

American Dryer Corp. ML-190, Руководство по установке

Поделиться
Скачать
American Dryer Corp. ML-190 Скачать руководство пользователя страница 35

113354 - 20

www.adclaundry.com

31

H.  STEAM INFORMATION

It is your responsibility to have 

ALL

 steam plumbing connections made by a qualified professional to ensure that

the installation is adequate and conforms to local and state regulations or codes.

IMPORTANT:

Failure to comply with the requirements stipulated in this manual can result in
component failure, which will VOID THE WARRANTY.

NOTE:

In standard format this dryer is manufactured with a pneumatic (piston) damper system, which
requires an external supply of clean, dry, and regulated air (80 psi ± 10 psi [5.51 bar ± 0.69
bar]).  Refer to 

Steam Damper Air System Connections

, 

Section H

, 

item 4

.  This dryer

may be 

provided with an optional steam solenoid valve, in which case, no pneumatic steam

damper system is provided.

1. Steam Coil pH Level

The normal pH level for copper type steam coils 

must be

 maintained between a value of 8.5 to 9.5.  For

steel type steam coils the pH level 

must be

 maintained between a value of 9.5 to 10.5.  These limits are set

to limit the acid attack of the steam coils.

IMPORTANT:

Coil failure due to improper pH level will VOID THE WARRANTY.

2. Steam Requirements – High Pressure

Standard (2) Stage Steam Coil
Inlet ________ 1-1/4” N.P.T. supply line connection – qty. two (2) at first (top) and third manifold.
Return ______ 1” N.P.T. return line connection – qty. two (2) at second and fourth (bottom) manifold.

Optional (1) Stage Steel Steam Coil
Inlet ________ 1-1/2” N.P.T. Supply Line Connection – qty. one (1) at top manifold.
Return ______ 1-1/2” N.P.T. Return Line Connection – qty. one (1) at bottom manifold.

Operating Steam Pressure

Maximum

125 psig

*

861.84 kPa

Heat Input (Normal Load)

14.5 Bhp

Consumption (Approximate)

465 lb/hr

210.9 kg/hr

Shaded areas are stated in metric equivalents

*  The minimum operating pressure for optimum results is 100 psig (689.47 kPa).

3. Installation Instructions

To ensure an adequate supply of steam is provided, be sure that the steam supply lines and steam return
lines are sized and laid out as stipulated in this manual.  Inadequate steam supply lines and steam return
lines or improper steam plumbing will result in poor performance and can cause component failure.  Clean,
dry steam 

must be

 provided to the dryer.

IMPORTANT:

Steam coil failure due to water hammer by wet steam will VOID THE WARRANTY.

Содержание ML-190































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды