manualshive.com logo in svg

American Dryer Corp. ML-190, Руководство по установке

Поделиться
Скачать
American Dryer Corp. ML-190 Скачать руководство пользователя страница 27

113354 - 20

www.adclaundry.com

23

F.  ELECTRICAL INFORMATION

1. Electrical Requirements

It is your responsibility to have 

ALL

 electrical connections made by a properly licensed and competent

electrician to ensure that the electrical installation is adequate and conforms to local and state regulations or
codes.  In the absence of such codes, 

ALL

 electrical connections, materials, and workmanship 

must

conform

 to the applicable requirements of the National Electrical Code ANSI/NFPA NO. 70-LATEST

EDITION or in Canada, the Canadian Electrical Codes Parts 1 & 2 CSA C22.1-1990 or LATEST EDITION.

IMPORTANT:

Failure to comply with these codes or ordinances, and/or the requirements stipulated
in this manual can result in personal injury or component failure.

NOTE:

Component failure due to improper installation will VOID THE WARRANTY.

Each dryer 

should be

 connected to an independently protected branch circuit.  The dryer 

must be

 connected

with copper wire only.  

DO NOT use

 

aluminum

 

wire;

 

it

 

could

 

create

 

a

 

fire

 

hazard

.  The copper

conductor wire/cable 

must be

 of proper ampacity and insulation in accordance with electric codes for

making 

ALL

 service connections.

NOTE:

The use of aluminum wire will VOID THE WARRANTY.

NOTE:

Wiring diagrams are affixed to the inside at the top front control door and the rear upper back
guard/panel or the left side panel area behind the control door.

Outside Ductwork Protection

To protect the outside end of the horizontal ductwork from the weather, a 90° elbow bent downward

should be

 installed where the exhaust exits the building.  If the exhaust ductwork travels vertically up

through the roof, it 

should be

 protected from the weather by using a 180° turn to point the opening

downward.  In either case, allow at least twice the diameter of the duct between the duct opening and the
nearest obstruction.

IMPORTANT:

DO NOT

 use screens, louvers, or caps on the outside opening of the exhaust

ductwork.

Содержание ML-190































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды