manualshive.com logo in svg

American Dryer Corp. ML-190, Руководство по установке

Поделиться
Скачать
American Dryer Corp. ML-190 Скачать руководство пользователя страница 38

34

American Dryer Corp.

113354 - 20

4. Steam Damper Air System Connections

In standard format, this dryer is manufactured with a pneumatic (piston) damper system, which requires an
external supply of compressed air.  (Note: this dryer may be provided with an optional steam solenoid valve
in which case, no steam damper system is provided.)  The air connection is made to the steam damper
solenoid valve, which is located at the rear inner top area of the dryer, just in front of the electric service
relay box (refer to the 

bottom illustration

 on 

page 35

).

a. Air Requirements

Shaded areas are stated in metric equivalents

b. Air Connection

Air connection to system — 1/4” Quick Connection

c. No air regulator or filtration is provided with the dryer.  External regulation/filtration of 80 psi (5.51 bar)

must be

 provided.  It is suggested that a filter/regulator/gauge arrangement be added to the compressed

air line just before the dryer connection.  This is necessary to ensure that correct and clean air pressure
is achieved.

5. Steam Damper System Operation

The dryer’s steam damper as shown in the 

top illustration

 on 

page 35

, allows the coil to stay constantly

charged eliminating repeated expansion and contraction.  When the damper is opened, the air immediately
passes through the already hot coil, providing instant heat to start the drying process.  When the damper is
closed, ambient air is drawn directly into the tumbler, allowing a rapid cool down.

Diagram 1

 shows the damper in the heating (open) mode, allowing heat into the tumbler.

Diagram 2 

shows the damper in the cool down (closed) mode, pulling ambient air directly into the tumbler

without passing through the coils.

NOTE:

With the dryer off or with no air supply, the steam damper is in cool down mode as shown in

Diagram 2 

at the top of 

page 35

.

Compressed

Air Supply

Air Pressure

 Normal

80 psi

5.51 bar

 Minimum Supply

70 psi

4.82 bar

 Maximum Supply

90 psi

6.21 bar

Содержание ML-190































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды