manualshive.com logo in svg

American Dryer Corp. ML-190, Руководство по установке

Поделиться
Скачать
American Dryer Corp. ML-190 Скачать руководство пользователя страница 33

113354 - 20

www.adclaundry.com

29

3. Piping / Connections

ALL

 components/materials 

must conform

 to National Fuel Gas Code Specifications ANSI Z223.1-LATEST

EDITION, or in Canada, CAN/CGA-B149.1-M91 (Natural Gas) or CAN/CGA-B149.2-M91 (Liquid
Propane [L.P.] Gas) or LATEST EDITION (for General Installation and Gas Plumbing), as well as local
codes and ordinances and 

must be 

done by a qualified professional.  It is important that gas pressure

regulators meet applicable pressure requirements, and that gas meters be rated for the total amount of

ALL

 the appliance Btu being supplied.

The dryer is provided with a 1-1/2” N.P.T. inlet pipe connection extending out the back area of the burner
box.  The minimum pipe size (supply line) to the dryer is 1-1/2” N.P.T.  For ease in servicing, the gas supply
line of each dryer must have its own shutoff valve.

The size of the main gas supply line (header) will vary depending on the distance this line travels from the
gas meter or, in the case of L.P. gas, the supply tank, other gas-operated appliances on the same line, etc.
Specific information regarding supply line size 

should be

 determined by the gas supplier.

NOTE:

Undersized gas supply piping can create a low or inconsistent pressure, which will result in
erratic operation of the burner ignition system.

Consistent gas pressure is essential at 

ALL

 gas connections.  It is recommended that a 1-1/2” (3.81 cm)

pipe gas loop be installed in the supply line servicing a bank of dryers.  An in-line pressure regulator 

must

be

 installed in the gas supply line (header) if the (natural) gas pressure exceeds 12.0 inches (29.9 mb) of

water column (W.C.) pressure.

NOTE:

A consistent water column test pressure of 3.5 inches (8.7 mb) for natural gas and 10.5 inches
(26.1 mb) for L.P. dryers is required at the gas valve pressure tap of each dryer for proper and
safe operation.

An 1/8” N.P.T. plugged tap, accessible for a test gauge connection, 

must be

 installed in the main gas

supply line immediately upstream of each dryer.

IMPORTANT:

Pipe joint compounds that resist the action of natural gas and L.P. gas 

must be

 

used.

IMPORTANT:

Test 

ALL

 connections for leaks by brushing on a soapy water solution (liquid

detergent works well).

WARNING: NEVER TEST FOR LEAKS WITH A FLAME!!!

IMPORTANT:

The dryer and its individual shutoff valve 

must be

 disconnected from the gas supply

piping system during any pressure testing of that system at test pressures in excess of
1/2 psig (3.5 kPa).

NOTE:

The dryer

 must be

 isolated from the gas supply piping system by closing its individual manual

shutoff valve during any pressure test of the gas supply system at test pressures equal to or less
than 1/2 psig (3.5 kPa).

Содержание ML-190































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды