American Dryer Corp. AD-285 Скачать руководство пользователя страница 29

Страница: 29 / 48

113235 - 5

www.amdry.com

I. PREOPERATIONAL TEST

ALL

dryers are thoroughly tested and inspected before leaving the factory. However, a preoperational test

should be

performed before the dryer is publicly used. It is possible that adjustments have changed in transit or

due to marginal location (installation) conditions.

1. Turn on electric power to the dryer.

2. Refer to the Operating Instructions for starting your particular model dryer.

a. When a gas dryer is first started (during initial start-up), it has a tendency not to ignite on the first

ignition attempt. This is because the gas supply piping is filled with air, so it may take a few minutes
for the air to be purged from the lines.

NOTE:

During the purging period, check to be sure that

ALL

gas shutoff valves are open.

NOTE:

Gas model dryers are equipped with a Direct Spark Ignition (DSI) system, which has
internal diagnostics. If ignition

is not

established after the first attempt, the heat circuit

in the DSI module will lock out until it is manually reset. To reset the DSI system, open
and close the main door and restart the dryer.

b. A gas pressure test

should be

taken at the gas valve pressure tap of each dryer to ensure that the water

column (W.C.) pressure is correct and consistent.

NOTE:

Water column pressure requirements (measured at the pressure tap of the gas valve
body):

Natural Gas ------------------------- 3.5 Inches (8.7 mb) Water Column.
Liquid Propane (L.P.) Gas -------- 10.5 Inches (26.1 mb) Water Column.

IMPORTANT:

There is no regulator provided in an L.P. dryer. The water column pressure

must

regulated at the source (L.P. tank), or an external regulator

must be

added to

each dryer.

3. Make a complete operational check of

ALL

safety related circuits

a. Door Switches

b. Hi-Limit Thermostats

c. Cycling Thermostat

d. Sail Switch

NOTE:

The sail switch can be checked for proper operation by opening the lint door while the
heating circuit (gas burner) is active (on). The heating until should shut off within a few
seconds. If not, make necessary adjustments to the sail switch.

4. Make a complete operational check of

ALL

operating controls.

Содержание AD-285

















































Результаты поиска

Содержание AD-285

Отзывы:

Похожие инструкции для AD-285

Бренды по названию

Популярные бренды

American Dryer Corp. AD-285, Руководство по установке

Результаты поиска

Содержание AD-285

Отзывы:

Похожие инструкции для AD-285

Бренды по названию

Популярные бренды