American Dryer Corp. AD-285 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 48

background image

16

American Dryer Corp.

113235 - 5

F. ELECTRICAL INFORMATION

1. Electrical Requirements

ALL electrical connections must be made by a properly licensed and competent electrician.

This is

to ensure that the electrical installation is adequate and conforms to local and state regulations or codes. In
the absence of such codes,

ALL

electrical connections, materials, and workmanship

must conform

to the

applicable requirements of the National Electrical Code ANSI/NFPA NO. 70-LATEST EDITION or in
Canada, the Canadian Electrical Codes Parts 1 & 2 CSA C22.1-1990 or LATEST EDITION.

IMPORTANT:

Failure to comply with these codes or ordinances, and/or the requirements
stipulated in this manual can result in personal injury or component failure.

NOTE:

Component failure due to improper installation will VOID THE WARRANTY.

Each dryer

should be

connected to an independently protected branch circuit. The dryer

must be

connected

with copper wire only.

DO NOT use aluminum wire, it could create a fire hazard

. The copper conductor

wire/cable

must be

of proper ampacity and insulation in accordance with electric codes for making

ALL

service connections.

NOTE:

The use of aluminum wire will VOID THE WARRANTY.

IMPORTANT:

A separate protected circuit

must be

provided to each dryer.

NOTE:

An individual ground circuit must be provided to each dryer, do not daisy chain.

IMPORTANT:

The dryer

must be

connected to the electric supply shown on the data label. In

the case of 208 VAC or 240 VAC, the supply voltage must match the electric
service specifications of the data label

exactly

.

IMPORTANT:

The wire size

must be

properly sized to handle the related current.

WARNING: 208 VAC AND 240 VAC ARE

NOT

THE

SAME

. Any damage done to dryer

components due to improper voltage connections will automatically VOID THE
WARRANTY.

NOTE:

Component failure due to improper voltage application will VOID THE WARRANTY.

NOTE: ADC

reserves the right to make changes in specifications at any time without notice or

obligation.

«
...
18
19
20
21
22
...
»

Содержание AD-285

















































Отзывы:

Нет отзывов

Похожие инструкции для AD-285

Бренд: GE Страницы: 8

Бренд: Sencor Страницы: 8

Бренд: HAEGER Страницы: 24

Бренд: wad Страницы: 27

Бренд: Aike Страницы: 4

Бренд: Frigidaire Страницы: 13

Бренд: Frigidaire Страницы: 12

Бренд: Miele Страницы: 56

Бренд: Miele Страницы: 13

Бренд: Miele Страницы: 80

Touchtronic T 1403

Бренд: Miele Страницы: 5

W 1213 WASHING MACHINE

Бренд: Miele Страницы: 56

Бренд: Miele Страницы: 88

TOUCHTRONIC T 8002

Бренд: Miele Страницы: 6

TOUCHTRONIC T 1303

Бренд: Miele Страницы: 86

Бренд: Miele Страницы: 100

Бренд: Miele Страницы: 100

TOUCHTRONIC T 8012 C

Бренд: Miele Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды