Amazone GHS 1500 Drive SmartCut Скачать руководство пользователя страница 95

Страница: 95 / 138

19. Open the drawbar hydraulic valve

20. Open the cutting deck hydraulic valve

NOTE

The hydraulic cylinder of the drawbar and
the hydraulic cylinder of the cutting deck are
connected in parallel. When both hydraulic valves
are open, the hydraulic cylinders of the drawbar
and cutting deck are actuated simultaneously.

CMS-I-00003367

21. lower the implement.

22. Lower the cutting deck.

23. Check whether the lower edge

of the cutting

deck is aligned parallel to the ground.

24. If necessary, adjust the height of the support

wheels.

CMS-I-00003734

6.9.8 Adjusting the front roller for scarifying

To use the front roller for scarifying, the front roller
must be adjusted to the cutting height.

REQUIREMENTS

The PTO shaft drive is switched off.

Adjust the cutting height using the crank, see
page 85.

Close the cutting deck hydraulic valve

Open the drawbar hydraulic valve

Lift the implement with the drawbar

until

the front roller has enough clearance to make
adjustments.

CMS-I-00003354

CMS-T-00005896-A.1

6 | Preparing the machine

Preparing the implement for operation

MG6212-EN-II | C.1 | 12.04.2021

Содержание GHS 1500 Drive SmartCut











































































































































Результаты поиска

Содержание GHS 1500 Drive SmartCut

Отзывы:

Похожие инструкции для GHS 1500 Drive SmartCut

Бренды по названию

Популярные бренды

Amazone GHS 1500 Drive SmartCut, Оригинальное руководство по эксплуатации

Результаты поиска

Содержание GHS 1500 Drive SmartCut

Отзывы:

Похожие инструкции для GHS 1500 Drive SmartCut

Бренды по названию

Популярные бренды