manualshive.com logo in svg

Amazone GHS 1500 Drive SmartCut, Оригинальное руководство по эксплуатации

Поделиться
Скачать
Amazone GHS 1500 Drive SmartCut Скачать руководство пользователя страница 100

10. Open the drawbar hydraulic valve 

1

.

The implement is prepared for mulching.

1

CMS-I-00004257

11.

To stop mulching,

Completely raise the grass collector.

12. Completely lower the grass collector again.

The mulch flap is open again and the mowed
material is conveyed into the grass collector
again.

6.9.10 Setting the implement for collecting on hard ground

This special setting is suitable for collecting leaves,
branches or waste on asphalt, paved or concrete
ground.

The cage roller for cutting height adjustment does not
have contact with the ground in this case.

REQUIREMENTS

The PTO shaft drive is switched off.

1.

Open the drawbar hydraulic valve 

1

.

2.

Open the cutting deck hydraulic valve 

2

.

NOTE

The hydraulic cylinder of the drawbar and
the hydraulic cylinder of the cutting deck are
connected in parallel. When both hydraulic valves
are open, the hydraulic cylinders of the drawbar
and cutting deck are actuated simultaneously.

1

2

CMS-I-00003367

CMS-T-00005900-A.1

6 | Preparing the machine

Preparing the implement for operation 

MG6212-EN-II | C.1 | 12.04.2021

94

Содержание GHS 1500 Drive SmartCut











































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды