Amana ACES80 Скачать руководство пользователя

Страница: 38 / 58

POLARIZATION AND PHASING

As more and more electronic's are introduced to the Heating

Trade, Polarization of incoming power and phasing of pri-

mary to secondary voltage on transformers becomes more

important.
Polarization has been apparent in the Appliance industry

since the introduction of the three prong plug, however, the

Heating Industry does not use a plug for incoming power,

but is hard wired.

Some of the electronic boards being used today, with flame

rectification, will not function properly and/or at all without

polarization of incoming power. Some also require phasing

between the primary and secondary sides of step-down

transformers.

THIS IS L1 OR THE

HOT POWER LEG

INCOMING POWER

THIS IS THE COMMON

OR NEUTRAL LEG

METER READS

120 VOLTS

METER READS

0 VOLTS

GN
D

VOLT / OHM

METER

VOLT / OHM

METER

These then should be wired to the furnace accordingly.

CHECKING FOR PHASING - PRIMARY TO SECONDARY OF UNMARKED TRANSFORMERS*

If meter reads approximately 96 volts - the primary to secondary are in phase - if reads approximately 144 volts out of

phase - reverse low voltage wires.

*NOTE:

For flame rectification the common side of the secondary voltage (24 V) is cabinet grounded. If you were to

bench test a transformer the primary neutral and secondary common must be connected together for testing purposes.

Some transformers will display phasing symbols as shown

in the illustration to the left to assist in determining proper

transformer phasing.
Checking for polarization and phasing should become a habit

in servicing. Let's start now.

NOTE:

Newer integrated ignition controls have a diagnostic

flash code for reversed polarity (Refer to

Troubleshooting-Di-

agnostic Chart

for LED Codes).

. .

VOLT / OHM

METER

TRANSFORMER

METER READS

24 VOLTS

LINE VOLTAGE

(NEUTRAL)

LINE VOLTAGE

L1 (HOT)

VOLT / OHM

METER

METER READS

120 VOLTS

VOLT / OHM

METER

VOLT / OHM

METER

READS 96 VOLTS - IN PHASE

VOLT / OHM

METER

READS 144 VOLTS - OUT OF PHASE

NEUTRAL

PHASING SYMBOL

24 V

120 V

Содержание ACES80



























































Результаты поиска

Содержание ACES80

Отзывы:

Похожие инструкции для ACES80

Бренды по названию

Популярные бренды

Amana ACES80, Инструкция по эксплуатации

Результаты поиска

Содержание ACES80

Отзывы:

Похожие инструкции для ACES80

Бренды по названию

Популярные бренды