background image

PRODUCT DESIGN

30

WARNING

I

F  THE INFORMATION IN THESE  INSTRUCTIONS  IS  NOT FOLLOWED  EXACTLY, A

FIRE  OR EXPLOSION  MAY RESULT CAUSING  PROPERTY DAMAGE, PERSONAL
INJURY OR  LOSS  OF LIFE.

–   

D

O  NOT  STORE OR  USE GASOLINE OR OTHER FLAMMABLE VAPORS  AND

    LIQUIDS IN  THE VICINITY OF THIS OR  ANY OTHER APPLIANCE.

– 

WHAT

 

TO

 

DO

 

IF

 

YOU

 

SMELL

 

GAS

:

 

• 

D

O NOT  TRY  TO LIGHT  ANY APPLIANCE.

 

• 

D

O NOT  TOUCH ANY  ELECTRICAL SWITCH; DO NOT  USE ANY

                      PHONE IN YOUR BUILDING.
 

• 

I

MMEDIATELY CALL YOUR GAS SUPPLIER  FROM A NEIGHBOR’S

 

   PHONE. 

F

OLLOW THE GAS  SUPPLIER’S  INSTRUCTIONS.

 

• 

I

F YOU CANNOT REACH YOUR GAS SUPPLIER, CALL THE  FIRE

                      DEPARTMENT.
–   

I

NSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER,

   SERVICE AGENCY OR  THE  GAS SUPPLIER.

3/8"

1/2"

5/8"

3/4"

7/8"

1/2"

3/4"

10

730

1,700

3,200

5,300

8,300

3,200

7,500

20

500

1,100

220

3,700

5,800

2,200

4,200

30

400

920

2,000

2,900

4,700

1,800

4,000

40

370

850

1,700

2,700

4,100

1,600

3,700

50

330

770

1,500

2,400

3,700

1,500

3,400

60

300

700

1,300

2,200

3,300

1,300

3,100

80

260

610

1,200

1,900

2,900

1,200

2,600

100

220

540

1,000

1,700

2,600

1,000

2,300

125

200

490

900

1,400

2,300

900

2,100

150

190

430

830

1,300

2,100

830

1,900

175

170

400

780

1,200

1,900

770

1,700

200

160

380

730

1,100

1,800

720

1,500

Pipe or

Tubing

Length

Feet

Tubing Size, O.D. Type L

Nominal Pipe Size

Schedule 40

Sizing Between First and Second Stage Regulator*

Maximum Propane Capacities listed are based on 2 psig pressure drop at 10 psig setting.
Capacities in 1,000 BTU/hour.

To convert to capacities at 15 psig settings - multiply by 1.130
To convert to capacities at 5 psig settings - multiply by 0.879

3/8"

1/2"

5/8"

3/4"

7/8"

1/2"

3/4"

1"

1-1/4" 1-1/2"

10

39

92

199

329

501

275

567 1,071 2,205 3,307

20

26

62

131

216

346

189

393

732 1,496 2,299

30

21

50

107

181

277

152

315

590 1,212 1,858

40

19

41

90

145

233

129

267

504 1,039 1,559

50

18

37

79

131

198

114

237

448

913

1,417

60

16

35

72

1,211 187

103

217

409

834

1,275

80

13

29

62

104

155

89

185

346

724

1,066

100

11

26

55

90

138

78

162

307

630

976

125

10

24

48

81

122

69

146

275

567

866

150

9

21

43

72

109

63

132

252

511

787

200

8

19

39

66

100

54

112

209

439

665

250

8

17

36

60

93

48

100

185

390

590

Tubing Size, O.D. Type L

Nominal Pipe Size

Schedule 40

Pipe or

Tubing

Length

Feet

*Data in accordance with NFPA pamphlet No. 54

Sizing Between Second or Second Stage Regulator & Appliance*

Maximum Propane Capacities listed are based on 1/2" W.C. pressure drop at 11" W.C. setting.
Capacities in 1,000 BTU/hour.

Propane Gas Piping Charts

WARNING

I

F THE GAS FURNACE IS INSTALLED IN A BASEMENT, AN EXCAVATED

AREA OR A CONFINED SPACE, IT IS STRONGLY RECOMMENDED TO
CONTACT A PROPANE SUPPLIER TO INSTALL A GAS DETECTING
WARNING DEVICE IN CASE OF A GAS LEAK. 

• 

S

INCE PROPANE GAS IS HEAVIER THAN AIR, ANY LEAKING GAS CAN

  SETTLE IN ANY LOW AREAS OR CONFINED SPACES. 
• 

P

ROPANE GAS ODORANT MAY FADE, MAKING THE GAS UNDETECTABLE

  EXCEPT WITH A WARNING DEVICE.

Содержание ACES80



























































Отзывы: