Amana ACES80 Скачать руководство пользователя

Страница: 54 / 58

SERVICING

COOL-H

PARK

S-314 CHECKING FLAME SENSOR

A flame sensing device is used in conjunction with the ignition

control module to prove combustion. If proof of flame is not

present the control will de-energize the gas valve and "retry"

for ignition or lockout.
The following drawings illustrate from a bottom view, the

approximate distances for the ignitor and flame sensor to

the gas inshot burner. You will note they are in the main

burner stream, not in the carry over ports as shown in the

following figure.

Flame Sensor

Models with Integrated Ignition

Control & Flame Sensor Probe

(80% Upflow Model Shown, Counterflow Similar)

WARNING

HIGH

VOLTAGE

ISCONNECT

ALL

POWER BEFORE SERVICING OR

INSTALLING THIS UNIT.

ULTIPLE POWER SOURCES MAY

BE PRESENT.

AILURE TO DO SO MAY CAUSE PROPERTY

DAMAGE, PERSONAL INJURY OR DEATH.

1. Disconnect the orange flame sensor wire from the sensor

2. Connect a micro-amp meter in series with this wire and

the sensor terminal.

3. Place the unit into a heating cycle.

INE VOLTAGE NOW PRESENT

WARNING

4. As soon as flame is established a micro-amp reading

should be evident once proof of flame (micro-amp read

ing) is established, the hot surface ignitor will be de-en-

ergized.

5. The Integrated Ignition controls will have 1 to 4 mi-

cro-amps. If the micro-amp reading is less than the

minimum specified, check for high resistance wiring

connections, sensor to burner gap, dirty flame sensor,

or poor grounding.

6. If absolutely no reading, check for continuity on all com-

ponents and if good - replace ignition control module.

NOTE:

Contaminated fuel or combustion air can create a

nearly invisible coating on the flame sensor. This coating

works as an insulator causing a loss in the flame sense sig

nal. If this situation occurs the flame sensor must be cleaned

with steel wool.

Содержание ACES80



























































Результаты поиска

Содержание ACES80

Отзывы:

Похожие инструкции для ACES80

Бренды по названию

Популярные бренды

Amana ACES80, Инструкция по эксплуатации

Результаты поиска

Содержание ACES80

Отзывы:

Похожие инструкции для ACES80

Бренды по названию

Популярные бренды