background image

Operation & Care Manual #824 • 3.

O P E R A T I O N A L   P R O C E D U R E S

 SET

prg

!

ERROR CODE

INDICATOR L.E.D.

HEAT/COLD

INDICATOR L.E.D.

CHAMBER

TEMPERATURE

L.E.D.

TEMPERATURE

SET

BUTTON

POWER
ON/OFF

ROCKER SWITCH

L.E.D.1

INCREASE / DECREASE

BUTTON

200

THERMOST

A

T

"I" = "ON"

   "

" = "OFF"

Thermostat Control Description and Function

The L.E.D., Light Emitting Diode, referred to is an electronic

device providing illumination.

The control has a three-digit L.E.D. display.  When the warm or

cold cabinet is in operation, the L.E.D. will show the chamber's

internal temperature.  The display will also show programming

and diagnostic information.

ON/OFF Rocker Switch

The Power On/Off Rocker Switch positions

may be marked with the international "

I

" for

On and "O" for Off.

UP/DOWN Arrow Rocker Button

The UP/DOWN arrow rocker button is used to

increase or decrease the set-point temperature.  The minimum set-

point temperature for the hot side is 90°F (32°C) while the maxi-

mum set-point temperature is 200°F (93°C).  The temperature

range for the cold side is 27°F to 40°F (3°C to 5°C).

SET Button

The SET button is used to display the current

set-point temperature or program a new set-point temperature.

Pushing the SET button once will display the set-point tempera-

ture value for five seconds.  Holding the SET button allows the

programming mode to become active.

L.E.D. Display

The L.E.D. display will show the set-point

temperature value when programming, or the

warm or cold chamber's temperature when

calling for heat or cold.  When programming a

new set-point temperature, the L.E.D.1 indi-

cator will blink.  When a new set-point tem-

perature is chosen, the Chamber Temperature

L.E.D. will flash three times to confirm.

POWER
ON/OFF

ROCKER SWITCH

 SET

°

F

CHAMBER

TEMPERATURE

L.E.D.

L.E.D.1

200

HEAT or COLD INDICATOR L.E.D.

The Heat or Cold  Indicator L.E.D. will illuminate

and remain lit while the unit is calling for heat or

cold.  It will go out when the air temperature

inside the chamber reaches the set-point 

temperature on the control.

ERROR CODE DISPLAYS

Open-Circuited

If "

ooo

" is displayed in the Error Code L.E.D.,

the sensor is open-circuited.  Follow Trouble

Shooting Guide instructions in this Operation

and Care Manual.  

Short-Circuited

If "

CCC

" is displayed in the Error Code L.E.D.,

the sensor is short-circuited.  Follow Trouble

Shooting Guide instructions in this Operation

and Care Manual.  

ERROR CODE INDICATOR L.E.D.

If either of the above mentioned errors codes

should occur, the Error Code Indicator L.E.D. will

be illuminated and remain so until error is cleared.

!

!

°

F

ERROR CODE

INDICATOR L.E.D.

INDICATOR L.E.D.

ERROR

CODE

DISPLAY

L.E.D.1

ooo

!

°

F

ERROR CODE

INDICATOR L.E.D.

INDICATOR L.E.D.

ERROR

CODE

DISPLAY

L.E.D.1

CCC

Содержание 1000-HCM

















Отзывы: