MT318-101
DUAL HDMI to HDBT TX
User’s Guide
400-0749-001
1
Welcome!
Everyone at Altinex greatly appreciates your purchase of the
MT318-101. We are confident that you will find it to be reliable
and simple to use. If you need support, please do not hesitate to
call us at 714-990-2300.
At Altinex, we are committed to developing unique and state of
the art Signal Management Solutions
®
for demanding audiovisual
installations. Welcome to the Altinex family of satisfied customers
around the world!
1. Precautions and Safety Warnings
•
Please read this manual entirely before using your
MT318-101. You can download a full version of this
manual at
. These instructions are to
ensure the reliable operation of your switcher and to
prevent fire and shock hazards. Please read them
carefully and heed all warnings.
1.1 General
•
Qualified Altinex service personnel or their authorized
representatives must perform all service.
1.2 Installation Precautions
•
To prevent fire or shock, do not expose this unit to water
or moisture. Do not place the MT318-101 in direct
sunlight, near heaters or heat-radiating appliances, or near
any liquid. Exposure to direct sunlight, smoke, or steam
can harm internal components.
•
Handle carefully; dropping or jarring can cause damage.
•
Do not pull any cables attached to the MT318-101.
1.3 Cleaning
•
Clean the MT318-101 with a dry cloth only. Never use
strong detergents or solvents such as alcohol or thinner.
Do not use a wet cloth or water to clean the card. Do not
clean or touch any component or PCB.
1.4 FCC Notice
•
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2)
this device must accept any interference received,
including interference that may cause undesired operation.
•
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 2 of
the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when
the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions found herein, may cause
harmful interference to radio communications. Operation
of this equipment in a residential area is likely to cause
harmful interference in which case the user will be
required to correct the interference at their own expense.
•
Any changes or modifications to the unit not expressly
approved by Altinex
, Inc. could void the user’s authority to
operate the equipment.
2. Installation Procedures
Note:
Download and read the full online manual to become familiar with the MT318-101 and for detailed installation instructions.
Note:
For best results, use the MT318-101 power to power the remote stand-alone receiver.
Do NOT power the stand-alone units with their supplier power adapter.
Step 1: Connect to the MultiTasker enclosure using RS232 at 115k baud or a TCP/IP connection; the IP address is visible on the front
panel LCD. The default IP address is 192.168.10.84 port 23.
Step 2. The MT318-101 is factory set to 9600 baud and RS232 receive disabled; RS232 transmit is always enabled.
[TRRSn=dddCii]
– Send data/enable receive
[TRTXn=dddCii]
– Send data/disable receive
[TRRSn=Cii]
– Enable receive
[TRTXn=Cii]
– Disable receive
n :
Port Number (1 or 2)
ddd : Serial data (%hh for hex)
Cii : Card ID (C1 to C20)
Step 3. The MT318-101 is identified by its slot number in the command section in this document.
Step 4: Use control commands to configure the RS232 baud rate, send RS232 data from the MT318-101 via the HDBT port to be
output at the HDBT receiver (UT260-104).
3. Warranty and Return Policies
Please visit the Altinex website at
for details on warranty and return policies. In the case of a unit needing repair,
please complete an RMA (return material authorization) form by clicking the Warranty link located on the bottom of the Altinex
homepage. Once completed, please email the form to
